Inside Mount vs Outside Mount Vertical Blinds

Compare inside mount and outside mount vertical blinds for a sliding door: how each headrail sits, what it needs from the frame, and how it affects light and clearance.

8 min read1 viewsInside Mount vs Outside Mount Vertical Blinds
— · 0 votes
Contents
  1. How the two mounts differ
  2. Check recess depth for an inside mount
  3. Plan the overlap for an outside mount
  4. Track clearance at a sliding door
  5. Light control and edge gaps
  6. Match the mount to the room layout
  7. Measuring and ordering the right size
  8. Fixing the brackets safely
  9. Vertical blind mount questions
  10. Is an inside mount or an outside mount better for a sliding door?
  11. Do outside mount vertical blinds let in less light at the edges?
  12. How much recess depth do inside mount vertical blinds need?
  13. What is track clearance on vertical blinds?
  14. Can vertical blinds be mounted on the ceiling instead of the wall?
  15. Which mount should I write on the order form?

Inside mount vertical blinds hang the headrail within the window or door opening, while outside mount vertical blinds attach the headrail to the wall or trim in front of the opening. The choice turns on the depth of the recess, how the slats need to travel, and how much clearance the sliding door has. Each mount changes the light gap, the walk-through space and the look of the room.

  • Inside mount vertical blinds need enough recess depth for the headrail and for the slats to turn without rubbing.
  • Outside mount vertical blinds sit on the wall or trim and cover the opening edges, which reduces light leaks at the sides.
  • A sliding door with little side room on the frame may suit an outside mount, because the track can extend past the opening.
  • Check track clearance before ordering, since the headrail depth and the slat swing decide how far the blinds project into the room.
  • The mount you pick changes where the brackets go, so measure the frame and the wall surface before you drill.

How the two mounts differ

Inside mount vertical blinds sit within the opening, with the headrail fixed to the top of the recess or to the ceiling above it. The slats hang inside the reveal, so the blind reads as part of the window or door rather than as an addition to the wall.

Outside mount vertical blinds fix the headrail to the wall face or to the trim around the opening. The track runs across the front of the recess, and the slats hang clear of the frame. This placement lets the blind cover the full opening plus an overlap on each side.

Both mounts use a headrail that carries a track, and both turn the slats to control light. The difference is where that headrail sits, which then decides the bracket type, the projection into the room and the size of the gap at the edges.

Check recess depth for an inside mount

Inside mount vertical blinds need a recess deep enough to hold the headrail and to let the slats rotate. Measure from the front of the frame to the back of the recess at the top, where the headrail will sit.

The headrail depth plus the swing of the slats sets the minimum. If the slats touch the frame or the glass when they turn, the blind will jam or wear. A shallow recess may force a smaller headrail or a different mount.

Squareness matters as much as depth. Measure the width at the top, middle and bottom of the opening, and use the narrowest figure for an inside mount. An out-of-square frame leaves gaps that no slat angle can close.

Plan the overlap for an outside mount

Outside mount vertical blinds attach to the wall or trim, so the headrail can be wider than the opening. A small overlap on each side and along the top helps the slats cover the edges and cut side light.

The overlap depends on the trim and the wall surface. A flat wall takes the bracket directly, while a molded trim may need a spacer or a different bracket so the headrail sits level. Note where the studs or solid fixing points fall before you choose the width.

An outside mount also changes how the blind meets a sliding door. The track can extend beyond the door opening, which lets the slats stack clear of the glass when the door slides open.

Track clearance at a sliding door

Track clearance is the free space the headrail and slats need to work without hitting the door, the handle or the surrounding wall. At a sliding door, the blind must clear the panel as it slides and the handle as it passes.

Inside mount vertical blinds keep the track within the recess, so the door panel travels behind the slats. Outside mount vertical blinds project into the room, and that projection must stay clear of the door swing and of any furniture placed near the opening.

Measure the distance from the door face to the nearest wall or cabinet. The headrail depth plus the slat swing must fit within that distance, or the slats will strike the obstacle when they turn.

Light control and edge gaps

Outside mount vertical blinds cover the perimeter of the opening, so they reduce the light that slips past the edges. Inside mount vertical blinds sit within the reveal, where a gap between the slats and the frame lets light through at the sides.

The size of that gap depends on how squarely the opening is built and how closely the blind is measured. A blind cut to the narrowest width of an uneven frame leaves a visible strip of light on the wider side.

Neither mount seals an opening completely, and vertical slats always leave some light between them when closed. Choose the mount that matches how much edge light you can accept in the room.

Match the mount to the room layout

Inside mount vertical blinds keep the headrail within the opening, which leaves the wall and floor space free. That suits a room where furniture, curtains or a radiator sits close to the window or door.

Outside mount vertical blinds add a projection at the top of the opening. Check that the projection does not clash with a sofa back, a shelf or a curtain track that runs past the door.

The site subject starts with the room you have, so sketch the footprint of the nearby furniture before you commit. A blind that projects into a walkway changes how the space feels, even when the slats are turned open.

Measuring and ordering the right size

Inside mount vertical blinds are ordered to the recess width and drop, taken at the narrowest and longest points. Outside mount vertical blinds are ordered to the opening plus the overlap you want on each side and at the top.

State the mount on the order, because the same opening needs different figures for each type. A supplier cuts the headrail and slats to the mount you name, and a mismatch leaves the blind short or too wide.

Write down the mount, the width, the drop and the fixing surface on one sheet. Take the measurements twice and compare them before you order, since a vertical blind is made to the figures you supply.

Fixing the brackets safely

Bracket placement follows the mount. Inside mount brackets fix to the top of the recess or the ceiling, and outside mount brackets fix to the wall or trim above the opening.

A vertical blind headrail carries real weight, so each bracket needs a solid fixing. Locate studs or suitable anchors before drilling, and avoid fixing only into plasterboard or drywall without the right anchor.

A wide sliding door blind or a heavy headrail may need a trained fitter, especially above a glass door or at height. Stop and call a specialist when the fixing surface is unclear or the bracket will not hold.

Vertical blind mount questions

Is an inside mount or an outside mount better for a sliding door?

Neither mount is right for every sliding door, and the door and recess decide. An inside mount suits a deep, square recess where the headrail clears the panel. An outside mount suits a shallow recess or a door that needs the track to extend past the opening for stacking room.

Do outside mount vertical blinds let in less light at the edges?

Outside mount vertical blinds reduce edge light because the headrail and slats overlap the opening on each side and along the top. Inside mount vertical blinds sit within the reveal, so a gap at the frame lets light past the slats. The overlap you add controls how much edge light remains.

How much recess depth do inside mount vertical blinds need?

Inside mount vertical blinds need a recess deep enough for the headrail plus the swing of the slats. The exact figure depends on the headrail depth and the slat width you choose. Measure the depth at the top of the opening, where the headrail sits, and check the slats turn without touching the frame.

What is track clearance on vertical blinds?

Track clearance is the free space the headrail and slats need to move without hitting the door, handle or wall. On a sliding door, the track must clear the panel as it slides and the handle as it passes. Measure the projection into the room before you pick a mount.

Can vertical blinds be mounted on the ceiling instead of the wall?

Ceiling mounting works with an inside mount when the recess reaches the ceiling, and it keeps the headrail out of the wall face. A ceiling fix needs a solid fixing point and enough drop for the slats to hang clear of the floor. Check the ceiling surface before you drill.

Which mount should I write on the order form?

Write the mount you have measured for, because the width figures differ between the two types. An inside mount uses the recess width at its narrowest point. An outside mount uses the opening width plus the overlap you want on each side.

Read next

Latest articles