How to Measure a Window for Blinds
Measure your window for inside or outside mount blinds with a tape measure. Get width, height, and recess depth right before you order a blind size.
Contents
- Gather the right measuring tools
- Decide between an inside mount and an outside mount
- Measure the width for an inside mount
- Measure the height for an inside mount
- Measure for an outside mount
- Record the recess depth and check the brackets
- Measure for each blind type
- Write the order and avoid the frequent errors
- Questions about measuring windows for blinds
- How do I measure a window for blinds with a tape measure?
- How do I measure a window for an inside mount blind?
- How do I measure a window for an outside mount blind?
- How do I measure blind size for roller, venetian, mini, and vertical blinds?
- Should I measure the window or the old blind?
- How deep does a window recess need to be for blinds?
Measuring a window for blinds means taking three width readings and three height readings with a tape measure, then working from the smallest width and the longest height. You also record the window recess depth, because that figure decides whether an inside mount will fit. Measure the window itself, not the old blind, and note whether the blind will sit inside the recess or hang over the frame.
- Take three widths and three heights in the recess, then use the smallest width and the largest height for an inside mount.
- For an outside mount, measure the width and drop you want the blind to cover, not the glass.
- Check the window recess depth against the mounting brackets before you order.
- Measure with a metal tape measure and write figures in the order the supplier asks for, width first.
- A blind size from a store shelf rarely matches a window, so confirm how each supplier labels width and drop.
Gather the right measuring tools
A metal tape measure is the tool for measuring a window for blinds, because a cloth tape can stretch and read short. Choose one long enough to span the full window in a single pull. A pencil, paper, and a step stool let you reach the top of tall windows safely.
Write each figure as you take it and label the width and the height clearly. Suppliers ask for width first and height second, and a swapped pair of figures produces a blind that does not fit. Round to the nearest whole unit the supplier requests rather than mixing fractions and decimals.
Note the window frame and the window recess on your sketch, since these two parts of the window drive the mounting decision. The recess is the shallow opening the window sits in, and the frame is the visible trim around the glass. Mark which side has a handle or a crank, because hardware can interfere with a blind.
Decide between an inside mount and an outside mount
An inside mount fits within the window recess, so the blind sits close to the glass and keeps the frame visible. An outside mount attaches to the wall or the frame and covers a larger area, which suits a window with little recess depth. The choice changes every measurement you take, so settle it before the tape measure comes out.
Inside mount blinds need a recess deep enough for the mounting brackets and the rolled or stacked blind. Measure the recess depth from the wall face to the glass at the top, middle, and bottom. A shallow recess can leave a roller blind tube or a venetian blind headrail standing proud of the wall.
Outside mount blinds need extra coverage beyond the window opening to control light at the edges. Plan the overlap on each side and at the top and bottom before you measure. A vertical blind for a sliding door is a typical outside mount, because the headrail usually runs across the wall above the opening.
Measure the width for an inside mount
Inside mount blind width comes from the narrowest point of the window recess, not from the glass. Pull the tape measure across the recess at the top, the middle, and the bottom. Record all three figures and keep the smallest one as the working width.
Walls are rarely square, so the three readings can differ by a noticeable amount. Using the smallest figure stops the blind from binding against the sides of the recess. Measure between the surfaces the brackets will touch, which may be the recess sides rather than the frame trim.
Check that nothing protrudes into the recess, such as a handle, a hinge, or an uneven plaster edge. A protruding fitting can reduce the usable inside mount blind width below your smallest reading. Measure again at the height of the fitting if the obstruction sits within the blind's travel.
Measure the height for an inside mount
Inside mount height runs from the top of the recess to the sill, and the longest of three readings sets the drop. Take a reading at the left side, the center, and the right side of the recess. Sills and headers are often out of level, so the figures can differ.
Use the longest height so the blind reaches the sill without a gap at the bottom. If the blind must clear a sill or a handle, decide where the bottom edge should finish before you order. Mention any such clearance to the supplier, because some blind types cannot be trimmed in height.
Some suppliers ask for the height of the glass only, while others want the full recess height. Read the ordering form for the blind type you chose and measure to the point it names. A roller blind and a venetian blind can use different reference points on the same window.
Measure for an outside mount
Outside mount blind width is the width of the area you want covered, which is wider than the window opening. Measure across the frame or wall at the point where the brackets will sit. Add the overlap you planned on each side to that figure.
Outside mount blind drop is the height from the top bracket line to the point where the blind should end. Measure from the chosen headrail position down past the sill if you want full coverage. A blind that stops at the sill leaves a light gap below it.
Check for obstructions on the mounting surface, such as a curtain rod, a light fitting, or an uneven wall. The headrail needs a flat, solid line to attach to, and brackets cannot grip a hollow or crumbling patch. Move the headrail line up or down if the surface at your first choice is unsuitable.
Record the recess depth and check the brackets
Window recess depth decides whether an inside mount blind can sit fully within the opening. Measure from the wall face to the glass at the top, the middle, and the bottom of the recess. Compare the smallest depth with the mounting brackets and the blind's hardware.
A roller blind needs room for the tube and the fabric roll, and a venetian blind needs room for the slat stack. Each blind type states the depth it requires, so match your smallest reading to that figure. A blind that fits too tightly can rub against the glass or the reveal.
If the recess is too shallow for an inside mount, an outside mount or a different blind type solves the problem. Record the depth on your sketch alongside the width and height. The supplier can then confirm the mounting option before the order is placed.
Measure for each blind type
Roller blinds, venetian blinds, mini blinds, and vertical blinds all use the same width and height readings, but they differ in how much clearance they need. Roller blinds need depth for the fabric roll, while venetian and mini blinds need depth for the stacked slats. Vertical blinds suit wide openings and sliding doors, and their headrail runs along the top of the opening.
A blind size listed on a store package refers to the blind itself, not to the window. Check whether the stated width includes the mounting brackets or the fabric only. Measuring the window first and matching it to the supplier's definition of blind size avoids a mismatch.
When you measure a window for blinds and curtains together, plan the curtain track position before the blind brackets go up. A curtain rod in front of an inside mount blind needs clearance so the fabric does not catch the blind. Note both the blind headrail line and the curtain line on the same sketch.
Write the order and avoid the frequent errors
A clear order lists the mounting type, the width, the height, and the recess depth for each window. Label each window by room and position so the fitter knows which blind belongs where. Keep the sketch with the order in case a figure needs checking.
The errors that spoil a blind order are measuring the old blind instead of the window, reading the tape at an angle, and mixing width and height. Measuring only the center of the window is another risk, because out-of-square recesses need the three-point check. Always confirm which figure comes first on the supplier's form.
If a window is very large, unusually shaped, or set in a wall you cannot safely reach, ask a trained fitter to measure and install. Blind brackets must anchor into solid material, and a poor fixing can let a heavy blind fall. Your own measurements are only as good as the access you have to the window.
Questions about measuring windows for blinds
How do I measure a window for blinds with a tape measure?
Use a metal tape measure and take three width readings and three height readings across the window recess. Keep the smallest width and the longest height for an inside mount. Write the figures down in the order the supplier requests, with width first.
How do I measure a window for an inside mount blind?
Inside mount blinds are measured within the window recess, at the narrowest width and the longest height. You also check the recess depth against the mounting brackets. Do not measure the glass alone, because the blind sits in the opening.
How do I measure a window for an outside mount blind?
Outside mount blinds are measured across the area you want covered, plus the overlap you plan on each side and at the bottom. Measure from the chosen headrail position to the point where the blind should end. The window opening itself is only the starting reference.
How do I measure blind size for roller, venetian, mini, and vertical blinds?
All four blind types use the same window width and height readings, but each needs different clearance for its hardware. Roller blinds need room for the fabric roll, and venetian and mini blinds need room for the slat stack. Check the supplier's definition of blind size before ordering.
Should I measure the window or the old blind?
Measure the window, not the old blind, because an existing blind may have been cut down or fitted loosely. Use the old blind only to see how it was mounted. Fresh readings from the recess or the wall give the figures the new blind needs.
How deep does a window recess need to be for blinds?
The required window recess depth depends on the blind type and its mounting brackets. Measure from the wall face to the glass and compare the smallest reading with the depth the blind states. If the recess is too shallow, choose an outside mount or a different blind.