How to Install Cable Tray on a Wall
Plan a wall-mounted cable tray run: bracket spacing, wall anchors for drywall or masonry, stud location, and keeping the tray level along the wall.
Contents
- Plan the tray line and mounting height
- Find studs and fix the wall brackets
- Anchors for drywall and masonry
- Wall cable tray questions
- How do I work out the cable tray mounting height?
- Can I fix a wall-mounted cable tray to drywall?
- What keeps the tray level along a long wall?
- Which wall anchors should I use for masonry?
Installing cable tray on a wall starts with one decision: mark the tray line first, then choose brackets and anchors that suit the wall material behind it. A wall-mounted cable tray holds cables off the floor and routes them in a straight, level run, so the mounting height and the fixing method matter more than the tray itself. This page explains how to plan the run, fix the wall brackets to drywall or masonry, and keep tray length and level true from end to end.
Plan the tray line and mounting height
Cable tray mounting height is set by where the cables come from and what sits below the run. Mark a straight line at the height you need, using a level to carry it along the wall before you drill anything. Check that doors, fittings and equipment clear the tray and its brackets. A level line marked first saves you from correcting a slope later.
Find studs and fix the wall brackets
Wall brackets carry the tray, so each one must reach solid material rather than just the surface. Locate studs with a stud finder and mark their centers along your tray line. Space the wall brackets close enough that the tray and its cables do not sag between them. Fix each bracket with the fastener your bracket maker specifies for that wall.
Anchors for drywall and masonry
Fixing to drywall or masonry needs different wall anchors, because the two materials hold a load in different ways. In drywall, anchors spread the load behind the board, and a bracket lined up on a stud is stronger than one in the hollow. Masonry needs a drilled hole and an anchor sized to the plug, with dust cleared out before the anchor goes in. Ask a trained installer when the wall material or the cable load is uncertain.
Wall cable tray questions
How do I work out the cable tray mounting height?
Cable tray mounting height follows the equipment the tray serves and the clearance you need below it. Measure from the highest connection point and from any doorway or machine the run passes. Mark that height on the wall and check it with a level before drilling. The right figure depends on your room, not on a standard number.
Can I fix a wall-mounted cable tray to drywall?
A wall-mounted cable tray can go on drywall when each bracket reaches a stud or uses anchors rated for the load. Line up the wall brackets on stud centers wherever the layout allows. Hollow drywall alone holds little, so a heavy tray or a long run needs solid backing or a different fixing plan. A trained installer can confirm what your wall will carry.
What keeps the tray level along a long wall?
Tray length and level depend on marking one straight line and checking it as you go. Use a level on each bracket as you fix it, and run a string or laser line down the full length. Correct a bracket before the next one goes on, so errors do not add up.
Which wall anchors should I use for masonry?
Wall anchors for masonry must match the drilled hole size and the load the bracket carries. Drill to the depth the anchor maker states, clear the dust, and seat the anchor fully. Loose or oversized holes weaken the fixing, so redrill if a hole is wrong. A specialist should specify anchors where the load is heavy or the wall is uncertain.
Read next
-
Cord Management for a Reading Nook
-
Cable Management Ideas for a Wall-Mounted TV or TV
-
Cable Management Ideas for a Computer or PC Desk
-
Why Cords and Wires Get Tangled
-
Is It Safe to Cable Tie Power Cords
-
Power Strip Ratings: Amps, Watts and Surge Ratings Explained
-
Cord vs Cable: What the Difference Is
-
Cable Clips for Extension Cords