Colour Rendering Index Range by Lamp Type (Fluorescent Tubes)
Learn the CRI range for fluorescent tubes, how T8 and T5 lamps differ, what the Ra value means and how to match a tube to the room's colour needs.
Contents
- What the colour rendering index measures
- The CRI range for fluorescent tubes
- T8 and T5 tubes compared by CRI
- Reading the Ra value on a tube label
- Matching CRI to the room you have
- Why the phosphor decides the score
- Where fluorescent CRI limits show
- Questions about fluorescent tube CRI
- What is the colour rendering index range for fluorescent tubes?
- Is a higher CRI always better for a fluorescent tube?
- Does a T5 tube render colour better than a T8 tube?
- Where do I find the Ra value on a fluorescent tube?
- Can I raise the CRI of a fluorescent fixture with a diffuser?
Fluorescent tubes cover a wide colour rendering index range, and the tube type and phosphor decide where a lamp sits on the CRI scale of 0 to 100. Standard halophosphate tubes render colour poorly, while tri-phosphor tubes reach a higher CRI band. The label on the tube, not the fixture, tells you the Ra value you are getting.
- CRI runs on a scale of 0 to 100, and a higher number means colours look truer under the lamp.
- Halophosphate fluorescent tubes sit at the low end of the CRI scale, with a visible dulling of reds.
- Tri-phosphor tubes cover the mid to high range and suit rooms where colour matters.
- The Ra value is printed on the tube or its specification sheet, so check it before you buy.
- Tube diameter and length do not set CRI; the phosphor blend inside the tube does.
What the colour rendering index measures
The colour rendering index is a score that compares how a lamp shows colours against a reference light source. The CRI scale runs from 0 to 100, and a lamp close to 100 shows colours much as daylight or an incandescent lamp would.
The score is built from test colour samples, and the general value is written as Ra. A lamp with a low Ra value shifts some hues, so a red fabric or a green wall can look muddy or gray under it.
CRI describes colour quality only, not brightness or light output. A tube can be bright and still score low on the CRI scale, which is why the two figures are read together on a lamp label.
The CRI range for fluorescent tubes
Fluorescent tubes as a group span a broad colour rendering index range, because the phosphor coating inside the tube decides the score. The range runs from roughly the low sixties up to the high nineties on the CRI scale.
Halophosphate tubes, the older phosphor type, sit at the bottom of that band. Their Ra value falls in the low range and their light dulls saturated colours, especially reds.
Tri-phosphor tubes sit higher, and the better blends reach the top of the fluorescent range. A tube sold for colour-critical work carries a high Ra value on its label, and that figure is the reliable guide.
T8 and T5 tubes compared by CRI
T8 and T5 tubes are the two linear fluorescent types you are likely to meet, and both are sold in low and high CRI versions. Tube diameter and length describe the fitting, not the colour quality.
A T8 tube is the wider of the two and fits many older fixtures. A T5 tube is narrower and runs in a slimmer fixture, and its higher output per length suits shallow ceiling coves and display cases.
The lamp type comparison for colour quality therefore comes down to the phosphor blend, not the tube family. Check the Ra value on the tube you plan to buy, because a T5 and a T8 with the same score will render colour alike.
| Tube type | Typical CRI band | Where the score comes from |
|---|---|---|
| Halophosphate T8 | Low band of the CRI scale | Older phosphor coating |
| Tri-phosphor T8 | Mid to high band | Blended tri-phosphor coating |
| Tri-phosphor T5 | Mid to high band | Blended tri-phosphor coating |
Reading the Ra value on a tube label
The Ra value printed on a fluorescent tube is the number to trust when you judge its colour rendering. Tube makers print a three-digit code, and the first two digits after the colour name give the Ra score.
A tube marked with a high Ra value renders colour close to the reference source. A tube marked with a low figure will shift hues, and no diffuser or reflector can correct that shift.
Colour temperature is a separate figure that describes warm or cool white, so read both numbers. A tube can have a warm tone and still carry a high Ra value, which is why the two figures sit side by side.
Matching CRI to the room you have
The room decides how much colour rendering quality you need from a fluorescent tube. A utility space such as a garage or a storage area tolerates a low CRI band, because colour accuracy there matters little.
A kitchen, a bathroom or a dressing area benefits from a high Ra value. Food, skin tones and clothing read truer under a tube in the upper band, and the room feels less gray.
A studio, a workshop for textiles or a home office for colour work needs the top of the fluorescent range. Where the tube cannot reach a high score, a specialist lamp is the better route, and an electrician can advise on the fitting.
Why the phosphor decides the score
The phosphor coating inside a fluorescent tube converts the ultraviolet discharge into visible light, and its recipe sets the CRI. A single halophosphate phosphor produces a modest spectrum, and the score stays at the low end.
A tri-phosphor blend combines three narrow emission bands, and the mix lifts the score toward the top of the range. The blend also sets the colour temperature, so the two figures come from the same coating.
Aging shifts the phosphor and can lower the Ra value over the life of the tube. Replace an old tube with a like-for-like high CRI tube when colour quality matters in the room.
Where fluorescent CRI limits show
A fluorescent tube with a modest Ra value shows its limits on saturated colours. Deep reds and strong blues lose depth, and a painted wall can look flatter than it does in daylight.
Skin tones under a low CRI tube can look slightly gray or greenish. A high CRI tube keeps skin tones closer to how they read outdoors, which matters in a bathroom or a dressing room.
Where colour accuracy is critical, check the Ra value before you fit the tube. A tube with a high score is the practical answer within the fluorescent family, and a specialist lamp is the answer beyond it.
Questions about fluorescent tube CRI
What is the colour rendering index range for fluorescent tubes?
Fluorescent tubes span roughly the low sixties to the high nineties on the CRI scale of 0 to 100. Halophosphate tubes sit at the low end, and tri-phosphor tubes reach the mid to high band. The Ra value printed on the tube gives the exact figure.
Is a higher CRI always better for a fluorescent tube?
A higher CRI means truer colour rendering, so it is better where colour accuracy matters, such as a kitchen or a dressing area. A low CRI tube is adequate in a garage or a storage space. The room, not the number alone, decides what you need.
Does a T5 tube render colour better than a T8 tube?
A T5 tube does not render colour better than a T8 tube by type alone, because both come in low and high CRI versions. The phosphor blend inside the tube sets the Ra value. Compare the printed scores, not the tube diameter.
Where do I find the Ra value on a fluorescent tube?
The Ra value sits in the colour code printed on the tube and in its specification sheet. The first two digits after the colour name give the score. Read the colour temperature beside it, since the two figures describe different things.
Can I raise the CRI of a fluorescent fixture with a diffuser?
A diffuser cannot raise the CRI of a fluorescent fixture, because the score comes from the phosphor inside the tube. A diffuser spreads light and softens glare, yet it leaves the spectrum unchanged. Swap the tube for a high CRI version instead.
Read next
-
Colour Temperature Chart and Kelvin Range for Lamps, Bulbs and Daylight
-
Flicker Index for LED Lighting
-
Choose Projector Brightness for a Bright Room
-
Cover Light Bulb Beam Angles: Understand Beam Spread and Choose the Right Angle
-
Warm White vs Cool White Christmas and Cluster Lights: Choosing for Light Output and Colour Quality
-
Warm White vs Cool White Lighting: Light Output and Colour Quality for Indoor and Outdoor Spaces
-
Light Levels for Different Room Activities: Measuring, Placing and Choosing Light for the Room You Have
-
Colour Rendering Index for Home Lighting: Matching CRI to the Room You Already Have