Butcher, Kraft and Wrapping Paper for Large Drawings

How to pick butcher, kraft or wrapping paper for large drawings: roll width, paper weight, what each surface takes, and how to tape a full-room plan in place.

4 min read6 viewsButcher, Kraft and Wrapping Paper for Large Drawings
— · 0 votes
Contents
  1. Reading roll width and paper weight
  2. Choosing kraft, butcher or wrapping paper
  3. Fixing a long sheet in place
  4. Questions about large drawing paper
  5. Can I use butcher paper for a drawing table?
  6. Is kraft paper good for drawing with charcoal and pencil?
  7. Can wrapping paper be used for drawing?
  8. How wide should a paper roll be for a full-room floor plan?

Butcher, kraft and wrapping paper for large drawings give you a wide, low-cost sheet for floor plans, sketches and full-room layouts. The choice comes down to three practical points: the width of the roll, the weight and thickness of the paper, and the drawing medium you plan to use. This page explains how each paper behaves, which one suits charcoal, pencil or marker, and how to fix a long sheet to a drawing table, wall or floor.

Reading roll width and paper weight

Paper roll width sets the widest single sheet you can cut without a seam, so measure your drawing surface size before you buy. A butcher paper roll sold for wrapping food can be narrow, while a kraft paper roll for drawing often comes in widths that cover a door or a tabletop in one piece. Paper weight and thickness tell you how the sheet feels and how much it resists tearing and bleed-through. Heavier stock holds up under erasing and repeated taping, while thin sheets buckle and cockle when wet media soak in.

Choosing kraft, butcher or wrapping paper

Kraft paper is the brown unbleached sheet that takes charcoal, pastel and pencil with a warm mid-tone background. White butcher paper gives a clean field for pencil and colored pencil, and it reflects light back so fine lines read more clearly. Wrapping paper for drawing works as an inexpensive option for quick studies, but check that the reverse is plain and uncoated before you commit. Charcoal and pencil on kraft paper suit concept sketches, while a bright white surface suits measured work you plan to scan.

Fixing a long sheet in place

Taping paper to a floor or wall starts with a clean, dry surface and low-tack tape so the sheet can be lifted without tearing. Run tape along the full length of each edge rather than at the corners alone, because a long sheet ripples and shifts under a hand. When you lay a full-room floor plan on paper, mark the room edges first and then draw the furniture footprints to scale inside them. A drawing table surface needs the same treatment, with the roll squared to the table edge before you cut.

Questions about large drawing paper

Can I use butcher paper for a drawing table?

Yes, butcher paper works on a drawing table when the roll is wide enough for your sheet and the paper is taped flat along every edge. Cut the sheet a little larger than the drawing area so tape sits outside the work. White butcher paper gives a bright surface for pencil, and the brown kraft type suits charcoal. Check that the paper weight is heavy enough to resist tearing at the taped edges.

Is kraft paper good for drawing with charcoal and pencil?

Kraft paper suits charcoal and pencil because its unbleached surface holds dry media well and provides a mid-tone backdrop. Soft charcoal lifts easily, so fix the finished drawing with a workable fixative spray in a ventilated space. Pencil lines stay visible on the brown tone, which helps when you lay out a plan before adding detail. Test your medium on a scrap of the same kraft paper roll before starting the full sheet.

Can wrapping paper be used for drawing?

Wrapping paper for drawing is workable for quick sketches and rough plans, though it is often thin and may tear under erasing. Choose a roll with a plain white or uncoated reverse and avoid glossy printed faces, which repel pencil and marker. Tape the sheet flat, because thin wrapping paper curls and buckles as it absorbs moisture. For a layout you plan to keep or measure from, a heavier butcher or kraft sheet serves better.

How wide should a paper roll be for a full-room floor plan?

A paper roll for a full-room floor plan needs a width at least as long as the longest wall you intend to draw, or you will join sheets with a seam. Measure the room and decide your scale before you buy the roll. Wider rolls avoid seams but cost more and demand a larger drawing table or floor area. If the room exceeds any roll width, plan the seam along a straight wall line where it hides.

Latest articles