Usable, Total, Gross and Covered Floor Area: Reading the Differences from Existing Floor Plans
Learn to interpret floor plan area labels and measure usable, total, gross and covered areas from existing drawings. Understand measurement boundaries, wall footprints, circulation space and shared areas to make better use of your space.
Contents
- What Is Total Floor Area and How Is It Measured?
- Total Floor Area vs Gross Floor Area: Where the Boundary Lies
- Usable Floor Area Definition and How to Find It on a Plan
- Usable Floor Area vs Gross Floor Area: A Practical Comparison
- Usable Floor Area vs Total Floor Area: The Influence of Internal Walls
- Usable Floor Area vs Usable Floor Space: Is There a Difference?
- Floor Area vs Covered Area: What the Plan Shows at Ground Level
- Reading Area Labels on Existing Floor Plans: A Step-by-Step Guide
- Measurement Boundaries: Inside Face, Outside Face, and Centrelines
- Wall Footprints: The Hidden Area That Reduces Usable Space
- Circulation Space and Shared Areas: How They Affect the Numbers
- A Comparison Table of Area Definitions
- Practical Example: Reading a Small Apartment Plan
- How to Apply This When Planning Changes to Your Space
When reading an existing floor plan, you will often see different area labels such as usable floor area, total floor area, gross floor area and covered floor area. They are not interchangeable, and each measures a different part of the building. Usable floor area is the actual space you can occupy and use within a room or tenancy, measured to the inside face of the enclosing walls. Total floor area is the sum of all usable areas on a floor, plus the area occupied by internal walls, columns, and other structural elements. Gross floor area extends to the outside face of the exterior walls and includes all enclosed space, often including stairwells, elevator shafts, and mechanical rooms. Covered floor area is the area of the building footprint that is covered by a roof, measured to the outside face of the exterior walls at ground level; it can include covered balconies or porticos. Understanding these distinctions helps you compare spaces, verify lease or purchase measurements, and plan changes realistically.
What Is Total Floor Area and How Is It Measured?
Total floor area is the entire area of a floor plate within the exterior walls. It is measured to the outside face of the exterior wall, which means it includes the wall thickness. It also includes all enclosed spaces, such as internal partitions, columns, shafts, and circulation areas like corridors and stairs (though local codes may have specific inclusions or exclusions). In a floor plan, the total floor area is often labelled as "TFA" or "Total Area" and may be shown as one figure for the whole floor. When reading a plan, locate the outermost line of the exterior walls; the area enclosed by that outline is the total floor area for that level.
Total Floor Area vs Gross Floor Area: Where the Boundary Lies
The difference between total floor area and gross floor area depends on the standard being used. In many contexts, they are used interchangeably and both refer to the area within the exterior walls including all internal elements. However, some standards distinguish gross floor area as including exterior wall thickness and all covered areas, while total floor area might be measured to the inside face of exterior walls, excluding the wall footprint. For example, the BOMA (Building Owners and Managers Association) standard defines gross building area as the total constructed area, measured to the outside face of exterior walls, and includes all enclosed floors. When comparing plans, check the legend or notes to see which measurement boundary was used. The key point is that gross floor area generally includes the wall footprints, whereas usable area does not.
Usable Floor Area Definition and How to Find It on a Plan
Usable floor area is the space within a room or suite that is actually available for use. It is measured to the inside face of the walls enclosing the space, meaning it excludes the thickness of those walls, columns, ducts, and other permanent obstructions. When reading a floor plan, usable area is often indicated by the inner dimensions of individual rooms or by a hatched area labelled "Usable Area". If the plan shows room dimensions, the area calculated by multiplying those dimensions (length × width) is the usable floor area of that room. For a whole office suite, the usable floor area is the sum of all individual room areas plus corridors within the suite, but it excludes common building areas like lobbies, shared restrooms, and elevator lobbies.
Usable Floor Area vs Gross Floor Area: A Practical Comparison
Usable floor area is always less than gross floor area for the same building. The difference is the area taken up by walls, columns, and common areas. The ratio of usable area to gross area is called the efficiency factor or load factor. For example, if a floor has a gross area of 1,000 m² and a usable area of 850 m², the efficiency is 85%. This means 15% of the gross area is not directly usable by the occupant but is necessary for building function. When comparing different spaces, a higher efficiency factor means more of the paid area is actually usable for your needs.
Usable Floor Area vs Total Floor Area: The Influence of Internal Walls
Total floor area includes the footprint of internal walls, while usable floor area excludes them. On a floor plan, if you measure the area of each room to the inside face of its walls and sum them, you get the usable floor area of the suite. If you then add the area of the walls themselves (their thickness times their length), you get the total floor area of the suite, assuming it does not include external walls or common areas. In a residential apartment, the usable floor area is often called "living area" or "net internal area", and the total floor area might be labelled "built-up area" or "plinth area", which includes wall thickness. This distinction matters when you are assessing how much furniture can fit and how spacious the rooms will feel.
Usable Floor Area vs Usable Floor Space: Is There a Difference?
The terms usable floor area and usable floor space are essentially synonymous. Both refer to the area that can be physically occupied and used, measured to the inside face of enclosing elements. However, "usable floor space" is sometimes used more loosely to describe the practical, unobstructed space after accounting for large furniture or fixtures. In professional plans, the formal term is "usable floor area" and has a precise measurement definition. Regardless of the label, it excludes walls, columns, mechanical shafts, and other permanent obstructions.
Floor Area vs Covered Area: What the Plan Shows at Ground Level
While floor area refers to the area of interior spaces on any level, covered floor area (also called footprint or ground coverage) is the area of land covered by the building at ground level. It is measured to the outer face of the exterior walls and includes all covered spaces, such as porches or carports that are roofed but may not be fully enclosed. Covered floor area is often used for zoning compliance and site coverage calculations. On a site plan, the covered area is the area of the building outline. It can be less than the gross floor area of a multi-storey building because it counts only the ground floor footprint, not the sum of all floors. Reading a floor plan, you may see both the "Ground Floor Covered Area" and the "Total Gross Floor Area"; the latter is the sum of all floor levels.
Reading Area Labels on Existing Floor Plans: A Step-by-Step Guide
To confidently interpret area labels on a plan, follow these steps:
- Identify the measurement boundary. Look for a note or legend that defines the area. Check whether dimensions are given to the inside face, outside face, or centreline of walls. This tells you which area type is likely shown.
- Look for hatched zones or polygons. Many plans shade or outline the exact area that is being calculated. The outline may run along the inside of exterior walls for usable area, or along the outside for gross area.
- Check for excluded spaces. Vertical penetrations such as stairwells, elevator shafts, and large ducts are often excluded from usable area but included in gross area. The plan may label them separately.
- Compare totalled areas. If the plan gives both usable and gross figures, calculate the difference. It should roughly equal the area of walls, columns, and common corridors.
- Use the scale bar. If no labelled areas are provided, you can measure the plan with a scale ruler and calculate areas yourself, applying the correct boundary conventions.
Measurement Boundaries: Inside Face, Outside Face, and Centrelines
The choice of measurement boundary directly determines the area type:
- Inside face of walls: Produces usable floor area. The line runs along the finished surface of interior walls, excluding wall thickness.
- Outside face of exterior walls: Produces gross floor area (or total floor area in some standards). The line runs along the outer surface of the building envelope, including wall thickness and sometimes cladding.
- Centreline of walls: Sometimes used for measuring common areas or between tenancies. It splits the wall area between adjacent spaces.
When reading a plan, the boundary line may be shown as a solid or dashed line with arrows indicating the measurement direction. Always verify which convention is used before comparing areas.
Wall Footprints: The Hidden Area That Reduces Usable Space
Wall footprints—the area occupied by the plan view of all walls and columns—can consume a significant portion of a building's gross area. In a typical office building, the wall footprint plus common areas can reduce usable area to 80–90% of gross area. When laying out furniture, every centimetre of wall thickness matters. A 200 mm thick internal wall reduces the usable width of a room by 200 mm compared to a 100 mm wall. Reading the plan, if you see thick wall lines between rooms, remember that the space inside the rooms is measured to the inside face of those walls; the line thickness itself often represents the wall footprint at scale.
Circulation Space and Shared Areas: How They Affect the Numbers
Circulation space—corridors, stairways, lobbies—is often a big factor in the difference between usable and gross area. In a multi-tenant floor, the common corridor outside your suite is not part of your usable area, but it is included in the floor's gross area. The usable area of the entire floor is the sum of each tenant's usable area plus the floor's common areas like public corridors and restrooms. When you rent space, you may pay for a share of these common areas, which explains why your rentable area is larger than your usable area. Reading a plan, identify which corridors are inside your demised premises (and thus part of your usable area) and which are outside (and thus common).
A Comparison Table of Area Definitions
| Area Type | Measurement Boundary | Includes | Excludes | Typical Use |
|---|---|---|---|---|
| Usable Floor Area | Inside face of enclosing walls | Actually occupiable space within a tenancy | Wall thickness, columns, common areas outside the tenancy | Space planning, furniture layout |
| Total Floor Area | Outside face of exterior walls (varies by standard) | All enclosed space on a floor, including walls and internal partitions | Open exterior spaces, roof overhangs (varies) | Building area calculations |
| Gross Floor Area | Outside face of exterior walls | All enclosed floor space, including vertical penetrations and mechanical rooms | Open balconies, exterior stairs (varies) | Building codes, lease comparisons |
| Covered Floor Area | Outside face of exterior walls at ground level | Building footprint, covered porches/porticos | Upper floors, uncovered decks | Zoning, site coverage |
Practical Example: Reading a Small Apartment Plan
Imagine a 60 m² one-bedroom apartment floor plan. The plan labels the apartment as "Gross Area: 72 m²" and "Usable Area: 60 m²". The 12 m² difference is the wall footprint and the share of common corridor and stairwell allocated to the apartment on that floor. Inside the apartment, the living room might be shown as 4.5 m × 5.0 m, but those dimensions are measured to the inside face of the walls. The plan may also show a dashed line around the apartment representing the "demised area", which is measured to the centreline of the party walls; that demised area might be 64 m². So you have three different numbers for the same apartment. Understanding these boundaries tells you exactly what space you can furnish (60 m²), what space you are responsible for maintaining (64 m²), and what space the building owner counts for leasing (72 m²).
How to Apply This When Planning Changes to Your Space
When you sketch a more useful corner or rearrange furniture, start with the usable floor area because that is the space you can actually occupy. Measure the room's inside dimensions from the plan, not the outside of walls. Take into account door swings, window placement, and fixed features like radiators or pipes that reduce usable floor space even though they are not subtracted from the formal area. If you are considering removing an internal wall, note that you will gain not only the area of the wall footprint but also the space previously needed for circulation around it. Conversely, adding a new wall will reduce the usable floor area of the rooms it separates, even if the total floor area remains unchanged. Always check the plan's area table and the scale bar to ensure your proposed changes fit within the available usable area.
By reading the differences between usable, total, gross and covered floor area on an existing plan, you can make informed decisions about furniture placement, remodeling, and lease terms. The numbers are not mere labels—they reflect physical boundaries that affect how you experience and use your space.
Related articles
Reading Floor Plan Scales and Converting Drawing Measurements
Learn to interpret floor plan scale ratios, use scale bars, and convert drawing measurements to actual dimensions for your own space planning.