Stud Finder for Plaster and Plaster Lath Walls

How to choose and set a stud finder for plaster and plaster lath walls, why old plaster misleads a sensor, and how to confirm a stud before you drill.

8 min read1 views
— · 0 votes
Contents
  1. Why plaster walls confuse a stud sensor
  2. Pick a scanner that reads through plaster
  3. Scan the wall in the right order
  4. Confirm a stud before you drill
  5. Handle metal lath and wire mesh
  6. Compare the tool types at a glance
  7. Set depth and sensitivity for thick plaster
  8. Plan the layout around the findings
  9. Questions about plaster wall stud finding
  10. Does a regular stud finder work on plaster and lath walls?
  11. How do I find a stud in an old plaster wall with metal lath?
  12. What depth setting should I use for a plaster wall?
  13. Why does my stud sensor beep everywhere on plaster?
  14. Can I trust a magnetic finder on plaster lath?

A stud finder for plaster and plaster lath walls needs a deep-reading sensor and a careful hand, because old plaster is thicker than drywall and often hides metal lath or a wire mesh. The tool does not find the stud directly; it reads a change in density, and you confirm that change before you trust it. Set the scanner to a deep mode, scan slowly, and mark both edges of the framing.

  • Choose a stud sensor with an adjustable depth setting, so it can read through thick plaster and lath.
  • Scan slowly and mark the edges of a stud, then test the middle with a thin nail.
  • Metal lath and old repairs can mimic a stud, so confirm every mark before drilling.
  • A wire mesh or metal lath layer may need an electronic scanner that separates metal from wood.

Why plaster walls confuse a stud sensor

Plaster and lath walls are built from several layers, and each layer changes what the sensor reads. Wood lath strips sit behind the plaster, spaced apart, so the gaps look like changes in density. A basic sensor may react to the lath instead of the stud behind it.

Plaster thickness varies from wall to wall, and a thick coat pushes the stud further from the sensor. A scanner depth setting that suits drywall may read only the plaster surface. Metal lath adds a second problem, because a sheet of expanded metal reflects the signal across the whole wall.

Old plaster walls also carry patches, keys and repairs that change density in small spots. The stud sensor reports these changes without knowing what causes them. Treat every reading as a hint, and plan a physical check before you cut.

Pick a scanner that reads through plaster

A stud finder for plaster walls should offer an adjustable scanner depth setting, often labeled deep or thick mode. The setting tells the sensor to look further into the wall. A tool with only one fixed depth may not reach the framing behind a thick plaster coat.

An electronic stud sensor that identifies metal and wood separately helps on metal lath. Some models show a live signal strength, which lets you watch the reading rise and fall as you move. A magnetic nail detection feature can also help, because it looks for the fasteners that hold the lath to the studs.

Match the tool to the wall, not to a brand claim. Read the stated depth range and compare it with your plaster thickness. Where metal lath covers the wall, a scanner with metal detection is the safer choice.

Scan the wall in the right order

Start the scan in an open area of the plaster wall and hold the sensor flat against the surface. Press it lightly and keep it still for a moment so the reading settles. A tilted tool reads the air gap and gives a false change.

Move the stud sensor slowly across the wall in one direction, then return along the same line. The slow pass lets the sensor register a change that a fast sweep would skip. Mark the first edge where the signal peaks, then scan from the other side to find the second edge.

Repeat the line at a second height on the same wall. A stud runs vertically, so two consistent marks line up. Where the marks disagree, the reading came from lath, metal or a patch, and the location is not settled.

Confirm a stud before you drill

Confirm every stud location on a plaster wall with a thin nail or a small drill bit. Drive it through the plaster at the marked center, and feel for the resistance of solid wood. A nail that passes through with little resistance has found a gap or a soft patch.

Use a nail long enough to pass the plaster and lath but short enough to stop before wiring or pipework. Check the wall for switches, outlets and plumbing before you probe. Where a service may run behind the plaster, a trained specialist should confirm the location.

Fill the test holes with a patching compound after the check, because plaster marks stay visible. Mark the confirmed stud edges with tape so the drill keeps its line. A confirmed stud is a reading you have tested, not one the tool reported.

Handle metal lath and wire mesh

Metal lath or a wire mesh behind the plaster spreads the sensor signal across the wall. The stud finder may report a broad band rather than a narrow stud. A magnetic setting that reacts to the mesh instead of the framing adds to the confusion.

An electronic scanner with a metal mode helps separate the mesh from the framing. Scan with the wood setting first, then check the same spot with the metal setting. A location that reacts to both settings is likely metal, and the wood reading there is not reliable.

Where a full metal layer covers the wall, the physical check becomes the deciding test. A small probe through the plaster, away from services, tells you whether wood sits behind. Stop probing and call a specialist where the wall carries wiring or pipework you cannot trace.

Compare the tool types at a glance

Three tool families suit plaster and lath walls, and each one answers a different question. A magnetic finder tracks the fasteners that hold the lath. An electronic stud sensor reads density changes through the plaster. A deep-reading scanner with metal detection covers both jobs on old walls.

The table below sets the types side by side for a plaster wall. The right choice depends on the plaster thickness, the presence of metal lath and the depth of the framing.

No tool replaces the physical check on a plaster wall. Choose the type that gives you a consistent reading, then confirm the mark with a nail before you drill.

Tool typeHow it reads plasterGood forLimit on old walls
Magnetic finderDetects screws and nails holding the lathLocating fasteners close to the surfaceMisses studs where lath is nailed off the line
Electronic stud sensorReads density change through the plasterFinding stud edges at moderate depthMay read lath gaps as studs
Deep-reading scannerAdjusts depth and can separate metalThick plaster and metal lathNeeds slow passes and a confirming probe

Set depth and sensitivity for thick plaster

The scanner depth setting controls how far the sensor looks into the wall. A plaster thickness beyond the drywall range calls for the deep setting. Start deep and reduce the setting only when the reading is unclear.

Sensitivity works with depth, and a high setting on a thin plaster wall reports every lath strip. Lower the sensitivity until the signal shows one clear peak. A stable peak at one line is easier to confirm than a wide band.

Test the setting on a wall where you know the stud, such as beside a door frame. The known spot shows how the tool behaves through your plaster. Carry that setting to the wall you plan to drill.

Plan the layout around the findings

Confirmed studs set the anchors for shelves, cabinets and wall art on a plaster wall. Spacing between studs decides how wide a shelf bracket can span. Note the stud lines before you compare furniture footprints or plan a corner.

Plaster walls carry weight through the lath and the studs, and a fixing in plaster alone holds little. Place heavy items on confirmed studs and use appropriate anchors for light items. A layout that follows the studs needs fewer test holes and less patching.

Draw the room with the stud positions marked, then place the furniture against that drawing. The measured layout shows where a tall unit can fix to framing and where a light item can hang free. A plan made this way survives the drill.

Questions about plaster wall stud finding

Does a regular stud finder work on plaster and lath walls?

A regular stud finder can work on plaster and lath walls, but its fixed depth may not reach the studs. Plaster is thicker than drywall, and the lath strips create density changes of their own. Set the tool to a deep mode where available, and confirm each mark with a thin nail.

How do I find a stud in an old plaster wall with metal lath?

Finding a stud behind metal lath needs a scanner with a metal setting, because the mesh reflects the signal across the wall. Scan with the wood setting, then check the same line for metal. Probe the marked center with a thin nail, and call a specialist where wiring or pipework may run behind the plaster.

What depth setting should I use for a plaster wall?

Use the deep or thick setting first on a plaster wall, then lower it if the reading is unclear. Plaster thickness varies, so test the setting beside a known stud such as a door frame. The known spot shows how far the sensor reaches through your wall.

Why does my stud sensor beep everywhere on plaster?

A stud sensor beeps everywhere on plaster when the sensitivity is too high or the tool reads metal lath. Lower the sensitivity until one clear peak appears. Move the tool slowly along one line, and treat a broad band as a sign of mesh rather than framing.

Can I trust a magnetic finder on plaster lath?

A magnetic finder on plaster lath finds the nails or screws that hold the lath to the studs, so it locates fasteners rather than the stud itself. The fasteners sit on the stud line, which makes the reading useful. Confirm the mark with a thin nail before you drill.

Read next

Latest articles