Sewing a DIY Bench Cushion

Learn how to sew a DIY bench cushion with a boxed edge: take bench top measurements, cut foam, choose upholstery fabric and add a zipper or ties.

10 min read8 viewsSewing a DIY Bench Cushion
— · 0 votes
Contents
  1. Planning DIY cushions for a bench seat
  2. Taking bench top measurements and making a template
  3. Choosing foam and upholstery fabric for a bench seat
  4. Cutting foam to size cleanly and safely
  5. Cutting fabric pieces for a boxed edge cover
  6. Bench cushion sewing steps for the cover
  7. Adding a zipper or ties to the cushion
  8. Fitting the finished cushion on the bench
  9. Bench cushion sewing questions
  10. Can you make a bench cushion without sewing?
  11. How thick should a bench cushion be?
  12. How much fabric do I need for a bench cushion?
  13. Do I need a special sewing machine for upholstery fabric?
  14. Should a bench cushion have a zipper or ties?

To sew a DIY bench cushion, you measure the bench top, cut foam and stitch a fitted cover. A boxed edge cover, made from a top, a bottom and a side strip, gives a crisp shape. A zipper lets you remove the cover for washing, while ties hold the cushion in place.

  • Measure the bench top at the front, middle and back, or trace a paper template.
  • Cut foam to the finished size and add seam allowance only to the fabric pieces.
  • Choose tightly woven upholstery fabric with an abrasion rating suited to daily seating.
  • Place the zipper on the back strip so it stays hidden against the wall.
  • Leave foam cutting to the supplier if you lack an electric knife or foam saw.

Planning DIY cushions for a bench seat

Planning a bench cushion starts with three choices: thickness, edge style and closure. Thickness depends on the seat height of the bench and the height of the table. A thicker cushion raises the sitter, so check knee room under the tabletop before deciding.

A boxed edge cushion has a separate side strip, called a boxing strip, sewn between top and bottom. The strip gives square corners and straight sides that sit neatly against a back wall. A knife edge cushion joins top and bottom directly, which is quicker but looks softer and thinner.

The closure decides how the cover comes off and how the cushion stays on the seat. A zipper allows the cover to be removed for cleaning or replacement. Ties or hook-and-loop tape keep a cushion from sliding on a smooth wooden bench. Some makers combine both, adding a zipper along the back and ties at the rear corners.

Taking bench top measurements and making a template

Accurate bench top measurements decide whether the finished cushion fits flush or leaves gaps. Measure the depth and length at the front, middle and back of the seat. Built-in benches can be slightly out of square, so readings may differ by a small amount. Note each reading rather than assuming the seat is a perfect rectangle.

A paper template captures angled ends, rounded corners and cutouts that a tape measure misses. Lay kraft paper or newspaper taped together on the seat and trace along the edges. Mark posts, wall trims and any notch where the cushion must clear an obstacle. Cut the template, test it on the bench, and trim until it sits flat with no overhang.

A corner bench cushion can be sewn as one L-shaped piece or as two straight pieces. Two pieces are easier to sew and lift, which helps on benches with storage underneath. At the corner, one cushion runs into the angle and the other butts against its side. An L-shaped single cushion has no seam at the corner but needs a larger template and more fabric.

Choosing foam and upholstery fabric for a bench seat

Foam for a bench cushion should be firm enough to support sitting without bottoming out. Foam firmness and density are listed by the supplier, and terms vary between makers. Higher density foam generally feels more supportive and resists flattening better than lighter foam. A layer of polyester batting wrapped around the foam softens the edges and fills the cover.

Upholstery fabric is woven heavier than dressmaking cloth and stands up better to friction from sitting. Look for a tight weave and an abrasion rating on the label or product sheet. Abrasion ratings, such as Martindale or Wyzenbeek results, describe how much rubbing a fabric resists in testing. Kitchen benches benefit from washable or stain-resistant fabric near food and spills.

Fabric pattern affects how much material you buy and how the pieces are cut. Stripes and large motifs need matching across the top and the boxing strip. Buy extra length for pattern repeats, shrinkage testing and mistakes during cutting. Prewash washable fabric before cutting if you plan to launder the cover later.

MaterialWhat to look forNotes
FoamFirm, high density seating foamThickness set by bench and table height
BattingPolyester wrapRounds edges and fills the cover
Upholstery fabricTight weave and abrasion ratingWashable fabric suits kitchen seating
ZipperHeavy upholstery zipper sold by lengthLong enough to wrap past back corners
ThreadStrong polyester or upholstery threadColor matched to the fabric

Cutting foam to size cleanly and safely

Foam cutting goes smoothest with an electric carving knife or a dedicated foam saw. A long serrated bread knife works on thinner foam but leaves rougher edges. Some foam suppliers offer cutting to your measurements, which removes the job from your list.

Mark the cut lines on the foam with a marker and a long straightedge. Cut the foam to the finished cushion size, not the fabric size. Keep the blade vertical and let it do the work rather than pressing down hard. Support the foam on a table edge so the blade passes cleanly below the cut.

Electric knives and saws are sharp, so keep hands behind the blade and away from its path. Unplug the tool before clearing foam crumbs from the blades. Clear foam scraps from the floor so cords and offcuts do not cause a trip.

Cutting fabric pieces for a boxed edge cover

A boxed edge cover needs a top panel, a bottom panel and a boxing strip. The top and bottom panels match the foam outline plus seam allowance on every edge. A seam allowance is the margin between the stitching line and the cut edge of the fabric. A half-inch allowance is a standard choice for upholstery seams.

The boxing strip wraps around the cushion sides and is as tall as the foam plus two allowances. For a zipped cover, split the back section into two narrow strips that hold the zipper. The zipper section should run past the back corners onto the sides for easier foam insertion. The remaining strip covers the front and sides and overlaps the zipper section at each end.

Lay all pieces on the fabric before cutting to check grain, pattern and total yardage. Grain is the direction of the threads, and pieces cut on grain hold their shape better. Mark the top of each panel and note which edge faces the front of the bench. Cutting a snug cover, rather than a loose one, keeps the fabric from wrinkling over the foam.

Bench cushion sewing steps for the cover

Sewing a boxed cushion cover begins with the zipper section, then joins it to the boxing strip. Stitch the two narrow zipper strips to each side of the zipper tape with a zipper foot. Sew the ends of the zipper section to the main boxing strip to form a closed loop. Check that the loop matches the full perimeter of the top panel before pinning.

The boxing loop is pinned to the top panel with right sides, the finished faces, together. Clip into the strip seam allowance at each corner so the fabric turns without puckering. Sew slowly around the corners, pivoting with the needle down at each point. A heavier needle, labeled for denim or upholstery, handles thick layers on a home machine.

Open the zipper partway before attaching the bottom panel, so the cover can be turned. Pin the bottom panel to the loop, aligning its corners with the top panel corners. Sew around the edge, trim bulky corners, and turn the cover right side out. Press seams with an iron at a temperature suited to the fabric fiber.

  • Sew the zipper between the two narrow back strips
  • Join the zipper section to the main boxing strip in a loop
  • Pin the loop to the top panel, right sides together
  • Clip corners and stitch, pivoting at each corner
  • Open the zipper and sew on the bottom panel
  • Trim corners, turn right side out and press

Adding a zipper or ties to the cushion

An upholstery zipper sold by the yard can be cut to any length the cushion needs. Slide a pull onto the chain, then stitch across the ends to stop the pull from escaping. Place the zipper on the back of the cushion so it faces the wall. Fold the foam slightly lengthwise to feed it through the opening, then flatten it inside.

Fabric ties hold a bench cushion to slatted backs, spindles or the legs of a seat. Cut strips of the cover fabric, fold the raw edges inward and topstitch them closed. Baste each tie, which means stitching it temporarily, into a back corner seam before assembly.

Built-in benches against a wall often have nothing to tie to, so other grips help. Non-slip rubber mesh placed under the cushion reduces sliding on painted or varnished wood. Hook-and-loop strips sewn to the cover base pair with strips fixed to the bench top. Adhesive strips can lift paint or varnish, so test them on a hidden spot first.

Fitting the finished cushion on the bench

A finished bench cushion should fill the cover fully, with crisp corners and no slack fabric. Wrap the foam in batting before inserting it to help fill the corners. Push the foam into each corner by hand, working from front to back. Smooth the batting as you go so no folds show through the fabric.

Check the fit by sitting along the full length of the bench and at the corner. Gaps at the wall may mean the template ran short or the seam allowance drifted. A cover that wrinkles across the top often needs a slightly thicker foam or extra batting.

Cover care depends on the fabric fiber and the cleaning code on the label. Remove the foam before washing, since wet foam is slow to dry inside a cover. Close the zipper before washing so the teeth do not snag other fabric. Spot clean fabrics that are not washable, and let them dry fully before refitting.

Bench cushion sewing questions

Can you make a bench cushion without sewing?

Yes, a no-sew bench cushion works by wrapping foam in fabric and stapling it to plywood. Fabric glue or iron-on hemming tape can also close a simple envelope cover. Such covers are harder to remove and wash than a sewn cover with a zipper.

How thick should a bench cushion be?

Bench cushion thickness depends on the seat height, the table height and how firm the foam is. Measure the space between seat and table underside, then allow enough knee clearance for a seated adult. Firmer foam can be thinner and still feel supportive, while softer foam needs more depth.

How much fabric do I need for a bench cushion?

The fabric amount for a bench cushion depends on the cushion size, fabric width and pattern repeat. Draw every piece with allowances on paper scaled to the fabric width to find the length. Add extra length when stripes or large motifs must match across the panels.

Do I need a special sewing machine for upholstery fabric?

No, a home sewing machine can sew many upholstery fabrics when fitted with a heavy needle. Use a needle sized for thick fabric, strong thread and a longer stitch length. Very thick vinyl, leather or stacked heavy layers may need an industrial machine or an upholsterer.

Should a bench cushion have a zipper or ties?

A bench cushion can have a zipper, ties or both, depending on cleaning needs and the bench design. A zipper makes the cover removable, and ties keep a cushion in place on benches with spindles. Built-in wall benches without anchor points do better with non-slip mesh or hook-and-loop strips.

Latest articles