How to Read a Light Meter: Readings, Units and Conversion

Learn how to read a light meter: what the display shows, the difference between lux and foot-candles, and how to convert readings with a simple factor.

8 min read0 views
— · 0 votes
Contents
  1. What a light meter reading shows
  2. Lux and foot-candles: the two illuminance units
  3. How to take a reading step by step
  4. Reading a lux meter display correctly
  5. Converting lux to foot-candles and back
  6. Why two meters can disagree
  7. Using readings to plan a corner
  8. Mistakes that spoil a good reading
  9. Questions about light meter readings
  10. What are light meter reading units?
  11. What is illuminance measured in?
  12. How do I check a light meter reading?
  13. How do I convert lux to foot-candles?
  14. How many lux equals one foot-candle?
  15. Why does my meter show a different number than another meter?

Reading a light meter means matching the number on the display to its unit, either lux or foot-candles, and to the spot the sensor is measuring. The reading tells you the illuminance on that surface, which is the light falling on it rather than the light a lamp gives off. Once you know the unit, you can convert it and compare measurements between rooms.

  • Check the unit first, since the same number means very different light levels in lux and in foot-candles.
  • Hold the sensor at the surface you care about, facing the light the way that surface does.
  • Illuminance is measured in lux or foot-candles, both of which describe light per area.
  • Multiply lux by 0.0929 to get foot-candles, or divide foot-candles by 0.0929 to get lux.
  • Read the meter after your eyes adjust and the lamp output settles, so the number is stable.

What a light meter reading shows

A light meter reading shows illuminance, the amount of light landing on a surface. The sensor converts that light into a number you read on the display. The number describes the surface, not the lamp, so moving the meter changes the reading.

Ambient light measurement works the same way in every room. The sensor sits in the space and collects light from every direction it faces. A reading taken beside a window and a reading taken in a corner of the same room can differ a lot.

Light sensor readings are a snapshot of one moment at one place. Lamp output shifts as a fixture warms up, and daylight shifts through the day. Write down where and when you took the reading, so you can repeat it and compare it fairly.

Lux and foot-candles: the two illuminance units

Illuminance is measured in lux or in foot-candles, and the unit tells you which system the meter uses. Lux is the metric unit and equals one lumen per square metre. A foot-candle is the imperial unit and equals one lumen per square foot.

The illuminance unit appears on the display or in the meter menu. Some meters show a small 'lx' or 'fc' next to the number. Others keep the unit in the settings, so check it before you write anything down.

Mixing lux and footcandles gives a false comparison, because one foot-candle equals about 10.76 lux. A room that reads 100 in one unit reads about 1076 in the other. Note the unit beside every figure you record.

How to take a reading step by step

Taking a reading starts with the sensor, because the sensor position decides the answer. Place the meter so its light-sensitive face sits where the surface would be. Keep your body behind the meter, so your shadow does not fall on the sensor.

Let the display settle before you note the number. Digital meters update as light changes, and the figure can flicker for a moment. Hold the meter still and wait for a steady value, then read it at eye level.

Repeat the measurement at a few points across the area you care about. One reading describes one spot, and a desk or a reading chair has light that varies across its surface. Record each point with its unit and its position in the room.

  • Check the unit shown on the display before you start.
  • Set the sensor at the height and angle of the surface you are judging.
  • Shade the sensor from your own body and from direct glare.
  • Wait for the number to steady, then write it down.
  • Take several points across the area and keep the lowest value.

Reading a lux meter display correctly

Reading a lux meter display means looking at three things: the number, the unit and the range. Some meters show a multiplier such as x10 or x100, and the true value is the display times that factor. Ignoring the multiplier gives a reading that is wrong by a large margin.

A display may also show a hold icon, a battery symbol or a mode label. The hold icon means the meter has frozen a value, so press the button again before you trust a new number. A low battery can make the display dim or unstable.

Some meters show a peak or maximum value beside the live reading. The live figure is the one to record for a surface, while the peak tells you about a flicker or a brief burst. Read the label above each number before you copy it.

Converting lux to foot-candles and back

Lux to foot-candle conversion uses one fixed factor, because both units measure the same thing. Divide a lux value by 10.7639 to get foot-candles. Multiply a foot-candle value by the same 10.7639 factor to get lux.

A light meter reading units calculator does the arithmetic for you, and a phone calculator with the factor works as well. Round the result to a sensible figure, since the meter itself has limited precision. Keep the original reading beside the converted one.

The conversion is only valid when the units are right. One lux equals about 0.0929 foot-candles, and one foot-candle equals about 10.7639104 lux. Convert the number, not the room, so the comparison stays honest.

ReadingUnitConverted value
100luxabout 9.3 foot-candles
100foot-candlesabout 1076 lux
500luxabout 46.5 foot-candles
50foot-candlesabout 538 lux

Why two meters can disagree

Two light meters can give different numbers for the same spot, because sensor design and calibration vary. A meter built for photography may weight the spectrum differently from a meter built for room surveys. The gap is a property of the instruments, not a sign that one is broken.

The angle of the sensor also changes the result. A bare sensor collects light from a wide field, while a diffuser dome spreads the response and evens it out. Point the sensor at the main light source and keep the same orientation for every reading in a set.

Compare meters under the same conditions and note which one you used. A reading is meaningful with its instrument and its unit attached. For decisions about a room, consistency across your own readings matters more than an exact match with someone else's meter.

Using readings to plan a corner

Light readings turn a vague sense of brightness into numbers you can plan around. Measure the spot where you want to read, work or place a chair, and note the lowest value across that area. That low figure is the one that limits how the corner feels.

Compare the reading with the task you plan for the corner. A task that needs sharp detail asks for more light on the surface than a spot for resting your eyes. A reading tells you whether the gap is small or large, and whether a lamp will close it.

Recheck the same points after you move a lamp or change a shade. Furniture placement changes shadows, and a tall shelf can block light from a window. Keep the meter and the unit the same, so the before and after numbers speak the same language.

Mistakes that spoil a good reading

A shadow on the sensor is the mistake that spoils a reading most often. Your hand, your phone or a nearby object can block light without you noticing. Step back and look at the sensor before you accept the number.

Reading too soon after switching on a lamp also distorts the result. Lamp output changes as the fixture warms, and some lamps need a short settling period. Note the waiting time you used, so a later reading follows the same routine.

Writing a number without its unit turns a useful measurement into a guess. Record lux or foot-candles every time, along with the place and the time. A small log of readings lets you compare a corner before and after a change.

Questions about light meter readings

What are light meter reading units?

Light meter reading units are lux and foot-candles, and both measure illuminance on a surface. Lux expresses lumens per square metre, while a foot-candle expresses lumens per square foot. Check which unit your meter shows before you record a number.

What is illuminance measured in?

Illuminance is measured in lux or foot-candles, depending on the unit system of the meter. Lux is the metric unit and foot-candles the imperial unit. Both describe the light falling on a surface, not the light a lamp emits.

How do I check a light meter reading?

Check a light meter reading by confirming the unit, placing the sensor at the surface, and waiting for a steady number. Repeat the measurement at a few points across the area. Compare figures only when they share the same unit.

How do I convert lux to foot-candles?

Divide the lux value by 10.7639 to convert lux to foot-candles. The result is smaller than the lux number, because one foot-candle equals about 10.76 lux. Round the answer to a sensible figure.

How many lux equals one foot-candle?

One foot-candle equals about 10.7639104 lux, which is the factor used in light meter reading units calculators. One lux equals about 0.0929 foot-candles. Use the same factor for every conversion in a set of readings.

Why does my meter show a different number than another meter?

Meters can show different numbers because sensor design, calibration and sensor angle vary between instruments. Compare meters under the same conditions and note which one you used. Consistency within your own readings matters more than an exact match.

Latest articles