Anchor a Bookcase to a Brick Wall
Learn how to anchor a bookcase to a brick wall with the right masonry drill bit, wall plugs and anchor bolts, plus tips for a tight, tip-over-safe fit.
Contents
- Decide where the anchor goes on the brick
- Choose the drill bit and the drill mode
- Clear the dust from the hole
- Fit the wall plug or masonry anchor
- Connect the bookcase to the wall bracket
- Keep the anchor clear of joints and edges
- Load the shelves and check the fixing
- Questions about anchoring bookcases to brick
- What kind of anchor do I use for a bookcase on a brick wall?
- Can I anchor a bookcase to a brick wall without drilling?
- What drill bit do I need for a brick wall anchor?
- How do I stop the bookcase from tipping if the wall is hollow?
- Should the anchor go into the brick or the mortar joint?
Anchoring a bookcase to a brick wall means drilling into the masonry with a bit matched to your anchor, then fixing a bracket or strap from the bookcase into the brick. The brick carries the load through a masonry anchor, so the bookcase cannot tip forward. Do the job with the correct drill mode, a dust-free hole and a bracket rated for the weight of a loaded shelf.
- Match the masonry drill bit to the anchor diameter and drill in hammer mode only, never in rotation-only mode.
- Clear dust from the hole before inserting a wall plug or anchor, or the fixing will loosen.
- Fix a metal bracket or strap to a stud or the top of the bookcase, then into the brick.
- Keep anchors in the brick body, away from mortar joints and the edges of the wall.
- Check the fixing after loading the shelves and tighten any bolt that has worked loose.
Decide where the anchor goes on the brick
Placement decides how well a bookcase anchor holds in a brick wall. Brick is strong in its body but weak at the mortar joints and near the edges, so plan the fixing point in the middle of a solid brick. A masonry anchor needs enough brick around it to grip.
Mark the height of the bookcase top and the bracket position on the wall before you drill. Hold the bracket against the brick and trace the hole centers with a pencil. Check that the marks sit on brick, not on a joint, and move the bracket slightly if they do not.
A wall with a hollow cavity or a thin veneer needs a different fixing from a solid brick pier. Tap the wall gently to judge what is behind the surface, and use a specialist anchor for hollow block. When you are unsure what the wall is made of, have a builder or structural specialist assess it before drilling.
Choose the drill bit and the drill mode
A masonry drill bit is the correct tool for brick, and its diameter must match the anchor or wall plug you plan to use. A bit that is too large leaves the fixing loose, while a bit that is too small stops the anchor entering. Buy the bit and the anchor as a matched pair.
Set the drill to hammer mode for brick, which combines rotation with a pulsing blow. Rotation-only mode will burn the bit and make slow progress in masonry. Start the hole slowly to stop the bit wandering across the hard surface.
Drill the hole slightly deeper than the anchor so dust and debris have somewhere to go. Keep the drill steady and straight, at the same angle as the bracket hole. A hole drilled at an angle makes the bolt sit crooked and weakens the fixing.
Clear the dust from the hole
Dust left in a drilled hole is the main reason a masonry anchor loosens over time. The dust coats the brick and stops the plug or anchor from gripping the sides. Clean the hole before you insert any fixing.
Blow out the hole with a pump or vacuum, then brush the inside with a small bottle brush. Repeat until no more dust comes out. A clean hole lets the anchor expand against bare brick.
Do not wet the hole or pack it with filler to make an anchor fit. Wet brick dust turns to paste and reduces grip. If the hole is too large, drill a fresh hole nearby in solid brick rather than filling the old one.
Fit the wall plug or masonry anchor
Wall plugs for brick and masonry anchors both grip by expanding against the sides of the hole. A plastic wall plug suits a lighter bookcase and a screw fixing. A metal masonry anchor, such as a sleeve anchor, suits a heavier bookcase and a bolt fixing.
Push the plug or anchor into the hole until it sits flush with the brick surface. Tap it gently with a hammer if it needs help, but stop if it will not enter. A plug that stands proud of the wall cannot hold the bracket tight.
Screw or bolt the bracket to the wall and tighten it firmly, but do not over-tighten a plastic plug. Over-tightening can spin the plug in the hole and strip the grip. Check that the bracket is solid and does not move when you pull it.
Connect the bookcase to the wall bracket
A metal L-bracket, a strap or a purpose-made furniture anchor links the bookcase to the wall fixing. Fix one side to the brick anchor and the other side to the top or back of the bookcase. The bracket must be strong enough for the loaded weight of the shelves.
Screw the bookcase side of the bracket into a solid part of the frame, not into thin back panel. A back panel can tear away under load. If the bookcase has no solid frame at the top, add a wooden cleat to the back and fix the bracket to that.
Pull the bookcase gently toward you after fitting to test the connection. Any movement means a screw is loose or the bracket is fixed to a weak part of the frame. Tighten or reposition the fixing before you load the shelves.
Keep the anchor clear of joints and edges
Brick edges and mortar joints give a masonry anchor very little to grip. Keep the hole at least a hand's width from the edge of the wall and away from vertical and horizontal joints. The middle of a brick face is the strongest point.
If the bracket falls on a joint, shift the bracket sideways or use a longer bracket to reach solid brick. Do not drill into a joint and hope the mortar will hold. Mortar crumbles under the load of a tall bookcase.
Corners and narrow piers need extra care because the brick is thin in both directions. Use a shorter anchor in a narrow pier and check that it does not break through the other side. Ask a specialist when the wall is thin or looks unstable.
Load the shelves and check the fixing
Load a bookcase from the bottom up and spread the weight across the shelves. Heavy items low down keep the center of gravity low and reduce the strain on the wall anchor. An evenly loaded bookcase is less likely to pull the fixing loose.
Re-check the anchor and the bracket after the shelves are full. Look for a gap at the wall, a loose bolt or a bracket that has shifted. Tighten any loose bolt with the correct tool and note the position.
Check the fixing again after a season of use, since vibration and changes in humidity can loosen a wall plug. A bookcase anchor protects people and property only while it stays tight. Replace a wall plug that has lost its grip rather than adding a second screw.
Questions about anchoring bookcases to brick
What kind of anchor do I use for a bookcase on a brick wall?
A masonry anchor such as a sleeve anchor suits a bookcase on a solid brick wall, while a plastic wall plug and screw work for a lighter unit. Match the anchor to the weight of the loaded bookcase and the strength of the brick. Choose a metal bracket or strap that connects the bookcase to that anchor.
Can I anchor a bookcase to a brick wall without drilling?
No, a reliable bookcase anchor in brick needs a drilled hole, because adhesives and clamps do not grip masonry well enough for a tall unit. Drilling lets a wall plug or masonry anchor expand against solid brick. Use a masonry drill bit in hammer mode and clear the dust before fixing.
What drill bit do I need for a brick wall anchor?
Use a masonry drill bit with a diameter that matches your wall plug or anchor exactly. A bit that is too wide leaves the fixing loose, and a bit that is too narrow stops the anchor entering. Drill in hammer mode and go slightly deeper than the anchor length.
How do I stop the bookcase from tipping if the wall is hollow?
A hollow or cavity wall needs a specialist cavity anchor rather than a standard wall plug. Standard masonry anchors grip solid brick but cannot expand against a hollow space. Have a builder or structural specialist identify the wall and choose the fixing before you drill.
Should the anchor go into the brick or the mortar joint?
Put the anchor into the body of the brick, not the mortar joint. Mortar crumbles under load and gives a wall plug little to grip. Shift the bracket so its holes land on solid brick, and keep the fixing away from the wall edges.