# Wallpaper Quantity Calculator: How Many Rolls You Need

Work out how many rolls of wallpaper a room needs from wall measurements, roll coverage, pattern repeat waste and deductions for doors and windows.

To find how many rolls of wallpaper you need, divide the total wall area by the coverage of one roll, then add extra for pattern repeat and offcuts. A wallpaper quantity calculator does the same math from your room dimensions and the roll size printed on the label. Measuring first is what keeps the roll count honest. 

- Measure wall height and the full perimeter of the room, then multiply to get wall area.
- Read the roll length and width from the label to get square feet or square metres per roll.
- Divide wall area by roll coverage and round up, never down.
- Add a pattern repeat allowance when the design must line up across strips.
- Deduct doors and windows only if you are confident the offcuts cannot be used.
 

## Start with room wall measurements 

Wallpaper quantity starts with the room wall measurements, taken before anything is ordered. Measure the height of each wall from floor to ceiling, or to the ceiling line where the paper stops. Write each figure down rather than holding it in your head. 

Next, measure the perimeter of the room, which is the total distance around all four walls. Multiply the perimeter by the wall height to get the wall area in square feet or square metres. A rectangular room with two long walls and two short walls still needs all four lengths measured separately. 

Sloped ceilings, alcoves and wall sections above doors change the shape of the surface. Break an uneven wall into rectangles and add the areas together. Keep the room dimensions on one sheet so the roll count can be checked later. 

## Read roll length and width for coverage 

Roll coverage comes from the roll length and width printed on the wallpaper label. Multiply length by width to get the square feet or square metres one roll covers. Roll sizes differ between manufacturers and between countries, so the label is the only reliable source. 

A narrow roll covers less wall per strip, which raises the number of rolls needed for the same wall area. Trim loss at the top and bottom of each strip also reduces usable coverage. Note the roll size before any division, because a different roll changes the whole calculation. 

Some wallpaper is sold in double rolls or in bolts, and the coverage figure applies to the pack rather than a single strip. Convert everything to one unit, either square feet or square metres, before dividing. Mixing units is the quickest way to get the number of rolls needed wrong. 

## The wallpaper calculation formula 

The wallpaper calculation formula is wall area divided by roll coverage, then rounded up to a whole roll. If a wall measures 120 square feet and one roll covers 30 square feet, the sum gives four rolls before any allowance. Rounding down leaves a wall unfinished. 

Strip count offers a second check on the roll count. Divide the perimeter by the roll width to see how many strips the room needs, then divide the wall height by the usable strip length to see how many strips one roll yields. The two methods should land close together. 

Calculating by strips handles pattern repeat and trim loss more honestly than area alone. Wall area divided by roll coverage works well for a plain paper with no matching. Use the strip method when the design must align, and treat the area figure as a rough guide. 
| Input | Where it comes from | Why it matters | 
| Wall height | Floor to ceiling measurement | Sets usable strip length | 
| Perimeter | Sum of all wall lengths | Sets number of strips | 
| Roll width | Wallpaper label | Strips per roll across the wall | 
| Roll length | Wallpaper label | Strips cut from one roll | 
| Pattern repeat | Wallpaper label | Extra paper per strip for matching |  

## Deducting doors and windows 

Door and window deductions lower the wall area, but only by the part that no strip will cover. A door reaching the floor removes a full-height section of wall. A window removes area in the middle of the wall, and the strips above and below it still get cut and hung. 

Many installers deduct nothing and keep the offcuts as spare paper. Offcuts above and below a window often fit another short section elsewhere. Deducting doors and windows too eagerly can leave the roll count short at the end of the job. 

A fair approach deducts a full-height door and keeps window area in the total. Where a large window or a set of glazed doors covers much of a wall, take the deduction and add spare paper for mistakes. The wallpaper calculator inputs should show whatever you decided, so the roll count can be repeated. 

## Allow for pattern repeat waste 

Pattern repeat allowance is the extra paper needed so the design lines up from strip to strip. A large repeat forces each strip to start at the matching point, which pushes more paper into the offcut. The repeat distance is printed on the label next to the design name. 

Straight match patterns align at the same height on every strip, and offset patterns shift by half a repeat. Both raise the waste allowance above a plain paper. A free match design needs only the trim allowance at top and bottom. 

Add one extra roll for a room with a large repeat and several walls, or work the repeat into the strip calculation. Pattern repeat waste is not a flaw in the measurement, it is part of the quantity calculation. Keep the figure visible when you hand the order to a supplier. 

## Work out rolls for one wall 

A single wall wallpaper job uses the same formula on a smaller scale. Measure the wall height and width, then multiply to get the wall area. Divide by the roll coverage and round up to the next whole roll. 

For a wall 10 feet wide and 8 feet high, the wall area is 80 square feet. If one roll covers 30 square feet, three rolls cover the wall with a small margin. A 10x12 wall gives 120 square feet and needs four rolls at the same coverage. 

One wall still needs a pattern repeat allowance when the design matches across strips. Add a spare roll when the wall holds a door, a radiator or a socket that interrupts the strips. Rolls per wall calculation is simple arithmetic once the wall area is known. 

## Rolls for a whole room or a small space 

Wallpaper quantity for a room follows the perimeter method, not a single wall. A 10x10 room has a perimeter of 40 feet, and at 8 feet high the wall area is 320 square feet. At 30 square feet per roll, that room needs eleven rolls before deductions and waste. 

A 10x12 room has a perimeter of 44 feet and a wall area of 352 square feet at the same height, which needs twelve rolls at that coverage. A 12x12 room reaches 384 square feet and thirteen rolls. A 10x8 wall is a single wall of 80 square feet and needs three rolls. 

A small bathroom or powder room has less wall area but more obstructions. Fixtures, a mirror and a shower enclosure break the strips into short lengths, which raises waste. Small bathroom wallpaper jobs often need a spare roll even when the area figure looks modest. 

## Check the roll count before you order 

Wallpaper rolls from room dimensions should be checked against the strip count before ordering. Compare the area method and the strip method, and use the higher figure. A difference of one roll between the two methods points to a measurement error or a pattern allowance you forgot. 

Confirm the batch and the roll size with the supplier, because a later order may not match. Buy the spare roll in the same batch as the main order. Store leftover paper flat, since a damaged roll cannot be replaced reliably. 

A wallpaper roll estimator is only as good as its inputs, so remeasure any wall that looks irregular. Ceiling height differences between rooms change usable strip length. Order on the final figure, not on the first estimate. 

## Questions about wallpaper roll counts 

### How do you figure out how many rolls of wallpaper you need? 

You multiply wall height by the room perimeter to get wall area, then divide by the coverage of one roll and round up. Add extra for pattern repeat and offcuts before you order. A wallpaper quantity calculator follows the same steps from your measurements. 

### How much wallpaper do I need for a 10x10 room? 

A 10x10 room with 8 foot walls has about 320 square feet of wall area, which is eleven rolls at 30 square feet per roll. Deduct full-height doors and add pattern repeat waste to the total. The roll size on your label decides the final count. 

### How much wallpaper do I need for a 10x12 room? 

A 10x12 room with 8 foot walls has roughly 352 square feet of wall area, or twelve rolls at 30 square feet per roll. A larger repeat or many openings pushes the figure up by a roll. Measure the actual ceiling height before ordering. 

### How many wallpaper rolls for one wall? 

One wall takes its height multiplied by its width, divided by roll coverage and rounded up. A 10x8 wall of 80 square feet needs three rolls at 30 square feet per roll. Add a spare roll when the design has a pattern repeat. 

### How much wallpaper do I need for a small bathroom? 

A small bathroom or powder room needs fewer rolls by area but more waste allowance. Fixtures and a mirror cut the strips into short pieces, so buy a spare roll. Work out the wall area first and then add the extra for pattern matching. 

### Should I deduct doors and windows from the wall area? 

You can deduct a full-height door, but keep window area in the total. Strips above and below a window are still cut and often fit elsewhere. Many installers deduct nothing and keep the offcuts as spare paper.
