# Standard Door Opening Sizes and Size Chart

Understand door opening dimensions, height and width, with a size chart in inches and millimeters and a clear method for measuring any opening before you order a door.

A standard door opening is the rough hole in the wall that receives a door frame, and its size depends on the door leaf plus the frame and clearance. The opening is wider and taller than the door itself, so the size chart separates rough opening sizes from finished door sizes. Measure width, height and wall thickness at several points before you buy anything. 

- The rough opening is larger than the door leaf by the frame thickness and a small clearance on each side.
- Door opening height is measured from the finished floor to the top of the rough opening.
- Door opening width is measured between the framed sides at the narrowest point.
- Interior and exterior doors follow different size ranges because exterior walls and thresholds differ.
- A size chart in inches and millimeters lets you compare a measured opening with available door sizes.
 

## What a door opening actually includes 

A door opening is the structural gap in a wall, and the door frame lines that gap before the leaf hangs. The rough opening is the unfinished hole left by the wall builder. The finished opening is the clear space after the frame and trim are fixed. 

Opening width and height refer to the rough opening unless a chart says otherwise. The door leaf is the moving panel, and it is smaller than the opening to allow for the frame, hinges and a small gap. Confusing the leaf size with the opening size leads to a door that does not fit. 

Wall thickness matters as well, because the frame must match the depth of the wall. A thick wall needs a deeper frame or an extension piece. Record the wall depth with the width and height so the opening is fully described. 

## How to measure door opening width 

Door opening width is the distance between the left and right sides of the rough opening. Measure near the top, the middle and the bottom of the opening. Use the smallest of those readings, because the frame must fit the tightest point. 

Take the measurement with the tape pulled straight and level. Note any skirting, plaster or flooring that narrows the clear space at the base. A doorway that looks square can be several millimeters narrower at one side. 

Write the width down in both inches and millimeters, since door suppliers may list one or the other. Keep the smallest width as the controlling figure. A frame that fits the narrowest point will fit the rest of the opening. 

## How to measure door opening height 

Door opening height runs from the finished floor level to the underside of the rough opening head. Measure at the left side, the center and the right side. Use the smallest reading as the controlling height. 

The finished floor matters, because a new floor covering raises the base and reduces the clear height. Decide the floor level before you measure. An opening measured over a bare subfloor can be too short once the finished floor is laid. 

Check that the head of the opening is level across its width. A sloping head means the frame will need packing or trimming. Record the height with the same care as the width and note the floor level you measured from. 

## Reading a door opening size chart 

A door opening size chart lists door leaf sizes next to the rough opening they need. The chart helps you compare a measured opening with available door sizes. Read the chart in the units your supplier uses and convert only after you have chosen a size. 

Charts in inches and millimeters describe the same sizes in different units. A chart row names the door leaf width and height first, then the rough opening width and height. The difference between the two sets of figures is the frame and clearance allowance. 

Use the chart as a guide, not as a substitute for measuring. Frame profiles and wall thickness vary between suppliers. Confirm the allowance with the door and frame you plan to buy before you cut or build anything. 
| Door leaf width | Door leaf height | Rough opening width | Rough opening height | 
| 30 in / 762 mm | 80 in / 2032 mm | 32 in / 813 mm | 82 in / 2083 mm | 
| 32 in / 813 mm | 80 in / 2032 mm | 34 in / 864 mm | 82 in / 2083 mm | 
| 36 in / 914 mm | 80 in / 2032 mm | 38 in / 965 mm | 82 in / 2083 mm | 
| 24 in / 610 mm | 78 in / 1981 mm | 26 in / 660 mm | 80 in / 2032 mm |  

## Interior door sizes and clearances 

Interior door sizes follow the room and the wall they serve, and the opening must allow for the frame and hinge clearance. A leaf that matches the chart still needs a rough opening wide enough for the frame. Check the swing side and the hinge side before you order. 

Bathroom and closet openings can be narrower than room doors, and the chart shows that range. A narrow opening limits furniture access, so measure the largest item that must pass through. Door opening dimensions for a tight room may need a wider leaf than the chart's smallest row. 

The frame allowance for an interior wall differs from an exterior wall because the wall depth differs. Confirm the wall thickness and the frame profile together. An interior opening measured without the skirting depth can end up too narrow for the frame. 

## Exterior door sizes and thresholds 

Exterior door sizes carry a taller threshold and a deeper frame than interior doors, and the opening must allow for both. The rough opening for an exterior door includes space for the sill and the weather seal. Measure the threshold height as part of the opening height. 

Exterior walls are often thicker, so the frame depth must match the wall. A frame that is too shallow leaves a gap at the inside face. Note the wall depth and the threshold detail before you compare the opening with the chart. 

Weather sealing and drainage belong to the exterior door assembly, and a trained installer should set the sill and seal. The opening size must suit the door system you choose. Do not cut a structural opening without advice from a qualified specialist. 

## Checking an opening before you order a door 

Check the opening for square, plumb and level before you order a door, because a twisted opening changes the clear sizes. Measure the diagonals of the opening and compare them. A difference between the diagonals shows the opening is out of square. 

Record the width, height, wall depth and diagonal readings on one sheet. Note the floor level and any services near the opening. Compare the smallest readings with the chart and the supplier's allowance for the frame. 

Where the opening is out of square or the wall is uneven, a trained carpenter or builder should correct it. Altering a structural wall needs specialist assessment. Leave the correction to a qualified trade and order the door after the opening is true. 

## Adapting a door to an existing opening 

Adapting a door to an existing opening means matching the leaf and frame to the measured rough opening. A frame can be packed or trimmed within limits, and the leaf can be reduced along its edges. The chart gives the starting size, not a custom fit. 

Trimming a door reduces its strength and its finish, so remove material only within the allowance the door maker states. A hollow-core door has a limited trimming margin at each edge. A solid door allows more, but the hinge and lock positions still constrain the cut. 

When the opening is far from any chart row, a made-to-measure door and frame is the reliable route. Give the supplier the smallest width, the smallest height and the wall depth. Let the supplier confirm the allowance before the door is made. 

## Door opening size questions 

### What are standard door opening dimensions? 

Standard door opening dimensions describe the rough opening that receives a frame and a door leaf. The opening is wider and taller than the leaf by the frame thickness and a small clearance on each side. The exact figure depends on the frame profile and the wall thickness, so confirm it with the door supplier. 

### How do I measure door opening height? 

Door opening height is measured from the finished floor level to the underside of the rough opening head. Take readings at the left, center and right of the opening and use the smallest one. Decide the finished floor level before you measure, because a new floor reduces the clear height. 

### Is a door opening the same as the door size? 

No, a door opening is not the same as the door size. The opening is the rough hole in the wall, while the door leaf is the moving panel that hangs inside the frame. The leaf is smaller than the opening to allow for the frame, hinges and a small gap. 

### What is the difference between interior and exterior door sizes? 

Interior and exterior door sizes differ because exterior doors include a threshold, a weather seal and a deeper frame. The exterior rough opening must allow for the sill and the wall depth as well as the leaf. Interior openings follow the thinner interior wall and the room they serve. 

### Where can I find a door opening size chart in inches and millimeters? 

A door opening size chart in inches and millimeters is supplied by door and frame manufacturers and by trade reference guides. The chart pairs door leaf sizes with the rough opening they need. Use the chart with your own measurements and confirm the allowance with the supplier. 

### Can I widen a door opening myself? 

No, widening a door opening is not a task for an untrained person, because the wall may carry a load or contain services. A structural opening needs assessment by a qualified builder or engineer. Leave the alteration to a trained specialist and order the door after the opening is finished.
