# How to Size a Bifold Door Opening

Measure a closet opening and read a bifold door size so the panels clear the frame, hinge on the pivot side and run on a straight track.

Sizing a bifold door opening means measuring the finished width and height of the framed hole, then choosing a door unit whose panels fit inside it and leave room for the track. The opening is the rough finished dimension, while the door size is the labeled width of the panel set. Those two numbers are related but not the same, so you measure the opening first and match the door to it. 

- Measure the finished opening at its narrowest point and its tallest point, not the framed stud cavity.
- A bifold door is labeled by the width of one panel or by the total width it covers, so confirm which figure you are reading.
- The track and header need room above the opening for the door to hang and swing.
- Leave clearance on the pivot side so the panel can fold back without rubbing the wall.
- Height matters as much as width, since a tall panel that scrapes the floor will not fold smoothly.
 

## Start with the finished opening, not the frame 

Sizing a bifold door begins with the finished opening, which is the clear width and height you see once the drywall or trim is in place. Measure the width at the top, the middle and the bottom of the opening, and record the smallest figure. Measure the height on both sides and at the center, and keep the smallest figure again. 

The framed rough opening behind the drywall is larger than the finished opening, and it is not the number you use to pick a door. A bifold door needs to fit the space the trim leaves, so the finished surfaces control the fit. If the trim is not installed yet, measure where its inner edge will land and use that line. 

Write the numbers down before you shop, because a closet opening is rarely perfectly square. A small difference between the top and bottom width tells you whether the frame is out of plumb. That knowledge helps you choose a door unit and decide if the frame needs adjustment first. 

## Understand what the door label measures 

A bifold door is labeled by the width it covers, and that figure can refer to the total pair or to a single panel width. Bifold panels arrive in pairs that fold and travel on a track. Confirm with the seller whether the labeled size is the panel width or the full opening coverage, because the two differ. 

The relationship between opening width and panel width is simple once the label is clear. Each pair of panels covers roughly the width of two panels when the door is closed. A pair that folds flat needs space to stack on the pivot side, so the folded stack takes about the width of one panel out of the opening. 

Opening width and height together set the size of the panel set you can install. A door sized for the opening still needs clearance at the top for the track and header and at the bottom for the floor surface. Check all three dimensions against the door specification rather than one alone. 

## Measure width at several points 

Measure the opening width with a tape held level, and take readings near the top, near the middle and near the bottom. The smallest reading is the true width the door must pass through. A closet opening that is wider at the top will not accept a door sized to that larger figure. 

Round down rather than up when the width falls between two labeled sizes. A door that is slightly narrower than the opening can be fitted with trim or a filler, while a door wider than the opening cannot enter it. Check the manufacturer's fitting allowance before you commit to a size. 

Bifold door panel width is the number that determines how the folded stack sits. Wider panels fold into a deeper stack and cover more of the opening when pulled closed. Narrower panels stack more tightly but need more panels to fill the same opening. 

## Check the height and the track and header 

The opening height sets the maximum panel height you can use, and the track and header must sit inside that figure. Measure from the finished floor to the underside of the head, since the track mounts there. A closet opening with a low head limits the door height you can install. 

The track and header carry the weight of the panels, so the head of the opening needs a solid surface to fasten into. A header is the horizontal member above the opening that gives the track something to grip. Drywall alone does not hold a track screw well, so check for framing or add a backer before you hang anything. 

Floor clearance matters as much as head clearance for a bifold. The bottom of each panel must ride above the finished floor without dragging. Check the door height against the floor surface you plan, and account for a threshold or a rug if one will sit in the opening. 

## Plan the pivot side clearance 

Pivot side clearance is the free space beside the hinge edge that lets the folded panels swing back. Each bifold pair pivots at the jamb on the hinge side and folds toward it. If a wall, a cabinet or a door casing sits too close, the panels bind as they fold. 

Measure from the hinge jamb outward to the nearest obstruction, and compare that figure to the depth the folded stack needs. The stack projects into the room by about the width of one panel when folded. A shallow recess or a tight corner can limit how far the door folds. 

Plan which side the door pivots on before you order, since a bifold pair is handed. Swapping the pivot side changes how the folded stack sits in the room. Look at the layout of the space around the closet opening and choose the side that leaves the most clearance. 

## Match the door to a standard opening 

A bifold door unit works with an opening that matches its coverage figure plus the fitting allowance the maker states. Match the opening width to the labeled door size, then check the height and pivot side against the same specification. The three figures together confirm the fit, and any one of them can rule out a door. 

When the opening does not match a labeled size, you have options that do not require cutting a door. Trim or a filler strip can narrow a slightly wide opening at the jamb. A pair of doors can also be hung as a double set, with pairs hinged at both jambs and meeting in the middle, when the opening is wide. 

Deal with an out-of-square opening before you fit the door. A frame that is out of plumb makes the track sit crooked, and a crooked track pulls the panels to one side. Correct the frame or add a shim behind the track rather than forcing the door into place. 
| What you measure | Where to measure | What it controls | 
| Opening width | Top, middle and bottom of the clear opening | Labeled door width and fitting allowance | 
| Opening height | Floor to underside of head, both sides | Panel height and track position | 
| Header depth | Above the opening, under the head | Room for track and fasteners | 
| Pivot side clearance | Hinge jamb outward to the nearest obstruction | How far the folded stack can swing | 
| Floor clearance | Bottom of panel to finished floor | Freedom to fold without dragging |  

## Fit the door without damaging the frame 

Hanging a bifold door is a two-person job on a wide opening, and a trained installer is worth calling when the frame is out of square or the header is not structural. Track screws must bite into solid framing, so confirm what is behind the head before you drill. A track pulled loose by a heavy panel can fall on a person. 

Set the track level and parallel to the head before you hang any panel. Test the fold with the door open and closed, and adjust the pivot and guide pins until the panels run without rubbing. Small adjustments at the track do more than force at the panel edge. 

Check the closing edge against the opposite jamb and the trim before you call the job done. A door that binds at the top usually needs a track adjustment rather than a shorter panel. Leave the fittings snug but not overtightened, since stripped screws in a header are hard to repair. 

## Bifold door opening questions 

### Do I measure the rough opening or the finished opening for a bifold door? 

You measure the finished opening, which is the clear width and height after the drywall and trim are in place. The rough opening is larger and sits behind the finished surfaces, so it does not tell you which door will fit. Measure the smallest width and height you find in the finished opening. 

### How wide should the opening be for a bifold door? 

The opening width should match the labeled coverage of the door unit plus the fitting allowance stated by the maker. Read the label carefully, because some sizes give one panel width and others give the full pair coverage. Measure the opening first, then compare it to the label with the allowance in mind. 

### How much clearance does a bifold door need on the pivot side? 

Pivot side clearance should be at least the depth the folded stack projects into the room, which is about one panel width. Measure from the hinge jamb to the nearest wall, cabinet or casing. Without that space, the panels bind as they fold back. 

### What is the track and header on a bifold door? 

The track is the rail the panels ride on, and the header is the horizontal member above the opening that holds the track. The header must be solid enough to take the track screws and the weight of the panels. Check for framing behind the head before you fasten anything. 

### Can I fit a bifold door in an opening that is out of square? 

A bifold door can work in a slightly out-of-square opening if you shim the track level before hanging the panels. A frame that is badly out of plumb needs correction first, since a crooked track pulls the doors to one side. Measure the width at the top and bottom to see how far out the frame is.
