# How to Measure a Garage Door Opening

Learn how to measure a garage door opening correctly: width and height, headroom, sideroom, backroom depth and track clearance for a replacement door.

Measuring a garage door opening means recording the finished width and height of the opening, then checking the clearances around it that let the door and its hardware move. You measure the opening itself, not the old door panel, and you note the headroom above, the sideroom beside it and the backroom depth behind it. A few consistent measurements let a supplier match a new door to the space you actually have. 

- Measure the opening between the finished jambs and from the finished floor to the head, not the old door.
- Check headroom, sideroom and backroom depth, because the door type depends on the space around the opening.
- Take each measurement at more than one point and use the smallest reading for width and height.
- Note anything that blocks the path of the door, such as a low ceiling, pipes or a step at the threshold.
 

## Start with the opening itself 

The garage door opening is the clear space a new door must fill, so measure it rather than the panel you are removing. Run the tape between the inner faces of the finished side jambs for the width. Measure from the finished floor to the underside of the head jamb for the height. 

Take the width at the top, the middle and the bottom of the opening. Garage openings are not always square, and the smallest of those readings is the width that matters. Repeat the height at the left edge, the center and the right edge, then keep the smallest figure. 

Write down the width first, then the height, in that order, because suppliers quote opening sizes that way. Note the thickness of the wall and the material of the jambs beside the figures. A photo of the opening with the tape in place helps a supplier check your numbers later. 

## Why headroom decides the door type 

Headroom is the clear distance from the top of the opening to the lowest obstruction on the ceiling above it. The track of a sectional door needs room to curve back, so headroom shapes which door and hardware fit. Measure upward at several points, because a beam, duct or light fitting can reduce the usable height. 

A sectional door swings back on horizontal tracks, and the radius of the track curve sets how much headroom it needs. A low headroom arrangement uses a tighter curve but takes up depth behind the opening. A one-piece door tilts outward and up, so it needs clear space above and in front rather than a long horizontal track. 

Record the position of anything that hangs below the ceiling, since a pipe across the path of the door blocks it even when the ceiling looks high. Measure from the top of the opening to that obstruction, not to the ceiling itself. Pass the figure to the supplier with the opening size. 

## Measure sideroom beside the opening 

Sideroom is the clear width between each side of the opening and the nearest wall or obstruction inside the garage. A sectional door needs vertical tracks that run up the wall beside the opening, and those tracks need space. Measure inward from both edges of the opening at floor level. 

Check the full height of the sidewall, not just the floor, because a protruding pier or a pipe can narrow the sideroom higher up. A sectional door with a torsion spring also needs room for the shaft and spring above the opening. Measure how far the sidewall stays clear from floor to ceiling on each side. 

Record both sides separately, even when the garage looks symmetrical. A garage with a door on one side and a wall close on the other still needs the tighter side noted. The narrower figure tells the supplier what the hardware can use. 

## Check backroom depth for the tracks 

Backroom depth is the distance from the opening to the rear of the garage, along the path the door travels when it opens. Horizontal tracks carry the open door into that space, so the depth must exceed the height of the door. Measure from the opening to the first obstruction at the back, such as a wall, step or stored equipment. 

Measure along the line the tracks will follow, not through the middle of the garage on a diagonal. Measure at a height near the top of the door, where the tracks run, because a low shelf at floor level does not block the door. A ceiling that slopes down toward the back reduces the clear path as the door travels. 

Take the depth at both track lines, since the garage may be deeper on one side. If storage racks, a water heater or a workbench sit in the path, measure to them rather than to the back wall. Clear the path or plan a door that opens differently, such as one that lifts vertically. 

## Match track clearance to the opening 

Track clearance is the free space around the opening that the door hardware occupies once it is installed. Vertical tracks sit close to the side jambs, and the horizontal tracks run back under the ceiling. The measured sideroom, headroom and backroom depth together define that clearance. 

Compare your three clearance figures with the requirements of the door you plan to buy. A supplier lists the headroom, sideroom and backroom depth that a given door and track radius need. When a figure falls short, the options are a different track radius, a different door type or a change to the structure. 

Moving a ceiling, a beam or a load-bearing wall is structural work, so a trained specialist should judge whether a change is possible. Do not cut a structural member to gain headroom on your own. Let the supplier confirm the door and track combination against your measurements before any work starts. 
| Measurement | Where to measure | What it governs | 
| Opening width | Between inner faces of the side jambs | Width of the new door | 
| Opening height | Finished floor to head jamb underside | Height of the new door | 
| Headroom | Top of opening to lowest ceiling obstruction | Track curve above the door | 
| Sideroom | Opening edge to nearest side obstruction | Vertical track and spring space | 
| Backroom depth | Opening to rear obstruction along track line | Length of horizontal track |  

## Record the measurements in a clear order 

A measurement sheet that a supplier can read without calling you back saves time and errors. Put the opening width and height first, since a door is ordered by those figures. Follow them with headroom, sideroom on each side and backroom depth, each labeled. 

State the unit beside every figure and keep one unit throughout the sheet. Note the date and whether the floor or ceiling is finished, because a later layer of flooring changes the height. Mark any obstruction you measured to, such as a pipe or a step. 

Take photos that show the tape against each measured surface. Stand back for one photo that shows the whole opening and the space around it. Send the sheet and the photos to more than one supplier if you are comparing quotations. 

## Check the floor and the header before ordering 

The floor at the opening and the header above it affect how the door sits and seals. Check that the floor is level across the opening, since a slope leaves a gap under the closed door. A threshold seal or a bottom weatherstrip can take up a small gap. 

Look at the header, the beam across the top of the opening, for sagging or damage. A sound header carries the weight of the door and its tracks. Note its material and condition for the supplier, and ask a trained specialist to assess any movement or cracking. 

Measure the height again after any floor work is finished, because the opening height you order depends on the final floor level. Confirm the width between the jambs is clear of trim and weatherstrip that will be removed. Final opening figures should describe the space the finished door will fill. 

## Questions About Measuring a Garage Door Opening 

### Do I measure the old door or the opening? 

Measure the opening, not the old door. The opening width runs between the inner faces of the finished side jambs, and the height runs from the finished floor to the underside of the head jamb. An old panel can be undersized or worn, so its size is not a reliable guide. 

### Where do I measure headroom? 

Headroom is measured from the top of the opening straight up to the lowest thing in the way, such as a beam, duct or ceiling. Take the reading at several points across the opening and keep the smallest one. That figure tells the supplier which track curve fits. 

### What is sideroom on a garage door? 

Sideroom is the clear distance from each edge of the opening to the nearest wall or obstruction inside the garage. The vertical tracks and the spring hardware use that space. Measure it on both sides and at more than one height, then keep the narrower figure. 

### How deep does the garage need to be behind the opening? 

The backroom depth must be at least the height of the door, because the open door lies along the horizontal tracks. Measure from the opening to the first obstruction along the track line, not to the far wall at floor level. Stored items in that path reduce the usable depth. 

### Can I fit a sectional door with low headroom? 

A sectional door can fit a low headroom space when the track uses a tighter curve, and the supplier confirms the minimum height for that arrangement. The trade-off is more depth needed behind the opening. A trained specialist should confirm the door and track combination for your measurements.
