# How to Install LED Strip Lights Under Cabinets

Plan and fit under-cabinet LED strip lights: measure the cabinet underside, mount with adhesive tape, route wires, and cut and connect strips safely.

Installing LED strip lights under cabinets means fixing a flexible light strip to the cabinet underside, then connecting it to a power adapter through a safe wire route. The job succeeds when you measure first, mount on a clean surface, and plan the cut points and connections before anything sticks. Planning the layout before you buy keeps the light where you need it and the cables out of sight. 

- Measure the cabinet underside and mark the run before you cut or mount anything.
- Clean and dry the mounting surface so the adhesive tape grips the cabinet underside.
- Cut strips only at the marked cut points and join sections with the matching connector.
- Keep the power adapter and every connection away from water, heat and moving parts.
- Route wires in channels or clips so they stay hidden and do not pull on the strip.
 

## Measure the cabinet underside first 

Start with a simple sketch of the cabinet underside and mark where you want light to fall. Measure each run from end to end and note the distance to the nearest power outlet. A measured layout shows how many strips you need and where a break or corner will interrupt the run. 

Decide whether the light should wash the counter evenly or pool over a work zone such as the sink or cutting area. The position of the strip matters more than its length, because a strip set too far back throws light onto the backsplash. Mark the mounting line on the cabinet underside with painter's tape before you commit. 

Check the space in front of the mounting line for door frames, drawer pulls and shelf brackets. A strip placed too close to a door edge shows as a bright glare line when the door is open. Write down the length of each run and the gap between runs so the order matches your sketch. 

## Choose a strip that fits the run 

An LED strip light is a flexible circuit board with small light-emitting diodes spaced along its length. Strips come in different brightness levels and in white or color-changing versions, and the spacing of the diodes affects how even the light looks. Compare the strip's rated output and its voltage before you match it to a power adapter. 

Some strips work on low voltage and need a separate driver, while others run on mains voltage with a built-in supply. Low-voltage strips are easier to cut and connect in short runs under a cabinet. Check the label for the voltage and the wattage per length, then confirm the adapter can carry the full run. 

A channel or profile is a slim metal or plastic housing that holds the strip and spreads the light. Channels protect the adhesive from heat and grease and give the strip a clean edge along the cabinet underside. Choose the profile depth to suit the cabinet lip and the light spread you want. 

## Prepare the cabinet underside for mounting 

Adhesive tape on the back of a strip holds only as well as the surface under it. Cabinet undersides collect grease, dust and wood fibers, so wipe the mounting line with a degreaser and let it dry fully. Skip this step and the tape will lift at the ends within days. 

Wipe the surface with a clean cloth after degreasing and check that no residue remains. A strip pressed onto a damp or oily cabinet underside will not bond, no matter how firm the pressure. Let the surface dry for as long as the cleaner label states before you peel the backing. 

Adhesive tape works on smooth painted or laminate surfaces, but raw wood and textured board need a mounting channel or clips. A channel screwed or stapled to the cabinet underside gives the strip a fixed base. Use the clips or channel the strip maker supplies when the surface is rough. 

## Cut and connect the strips 

LED strip lights can be cut only at the marked cut points printed along the strip. Cutting between those marks breaks the circuit and leaves a dead section, so follow the line exactly. Measure twice against your sketch before the blade goes in. 

Join cut sections with the connector type that matches the strip, such as a solderless clip or a short jumper lead. Keep the polarity right, because a reversed connection leaves the strip dark even when the adapter works. Test each joined section on the bench before it goes up under the cabinet. 

Corners need a short jumper or an angled connector so the strip can turn without bending sharply. A sharp fold can crack the circuit board and damage the diodes. Leave a little slack at each corner and route the jumper behind the cabinet frame. 

## Fix the strip to the cabinet underside 

Under-cabinet mounting works with the adhesive tape on the strip or with clips and a channel. Peel a short section of backing, press the strip onto the marked line, and work along the run in short steps. Pressing the whole strip at once traps air and leaves bumps. 

Keep the strip straight and parallel to the cabinet front edge so the light line looks even. At the end of each run, press the last few inches firmly, since the ends lift first. If the strip sits in a channel, slide it in before you fix the channel to the cabinet. 

Check the strip from below with the doors open and the room light off. Move any section that throws glare onto a door or shows a hot spot on the counter. Small adjustments now are easier than lifting a bonded strip later. 

## Plan the wire routing and power 

Wire routing keeps the cable out of sight and away from heat, water and moving parts. Run the low-voltage lead along the back of the cabinet and down to the power adapter. Use clips or a self-adhesive channel so the cable does not hang loose. 

The power adapter needs a ventilated spot near an outlet and clear of the sink and the hob. Keep the adapter and its connections above any place where water can splash or collect. A licensed electrician should handle any connection to household wiring, and a qualified person should fit a permanent supply. 

Leave a small service loop at each connection so the cable is not under tension. Label the adapter and the switch so you can find them later without taking the cabinet apart. Test the full run before the cable is fixed in its final route. 

## Test, finish and keep it safe 

A full test with the room light off shows whether the run is even and the joins hold. Switch the strip on and check every section for dark patches or flicker. Tighten any connector that moves and re-press any lifted end. 

Heat is the main risk with any strip light, so keep the strip and adapter clear of insulation and enclosed spaces. A strip that sits in a sealed channel without airflow runs hotter than one in an open profile. Follow the maker's clearance guidance for the strip and the adapter. 

Drilling or screwing into a cabinet underside can hit wiring or pipes hidden in the wall or cabinet. Check for services before a drill goes in, and stop if you are unsure what lies behind the panel. A trained specialist should handle any work near concealed wiring. 

## Questions about under-cabinet LED strips 

### Can I install LED strip lights under cabinets myself? 

Yes, a low-voltage LED strip that plugs into an outlet can be fitted by a careful do-it-yourselfer. The work involves measuring, cleaning the cabinet underside, cutting at the marked points, and routing the low-voltage cable. Any connection to household wiring needs a licensed electrician. 

### Where should the strip sit on the cabinet underside? 

The strip belongs near the front edge of the cabinet underside, set back far enough to hide the diodes from a standing view. A position close to the front edge washes the counter evenly. Mark the line with tape and check the glare with the doors open before the strip is fixed. 

### Do I need a channel for LED strip lights under a cabinet? 

A channel is not required on a smooth painted or laminate cabinet underside, where the adhesive tape can hold. A channel or clips help on rough wood, over a sink, or where the strip needs protection from heat and grease. The channel also spreads the light and hides the bare strip. 

### How do I connect two strips around a corner? 

Join two strips around a corner with a short jumper lead or an angled connector that matches the strip. Keep the polarity correct and avoid folding the strip sharply. Test the joined sections on the bench before mounting them. 

### What power adapter does an LED strip need? 

The adapter must match the strip's voltage and carry the total wattage of the full run. Add up the wattage per length for every section on that adapter, then choose a supply rated for that load. A mismatched adapter can overheat or leave the strip dim.
