# How to Install a Cable Tray

Learn how to install a cable tray under a desk or on a wall, from planning the route and choosing brackets to fixing sections and loading cables neatly.

To install a cable tray, mark the route, fix brackets, attach the tray and load the cables. A desk or wall tray for plug-in cords needs only a drill, level and suitable screws. Trays that carry fixed building wiring are work for a qualified electrician. 

- Measure the cable run and every device before you buy the tray.
- Follow the support spacing printed in the tray maker's instructions.
- Check walls for hidden wires or pipes before you drill any hole.
- Keep power and data cables apart where the tray allows a divider.
- Leave mains wiring and fixed electrical tray systems to a qualified electrician.
 

## Cable tray types for homes and offices 

A cable tray is an open channel that holds cords along a desk, wall or ceiling. The tray lifts cables off the floor and keeps them in one tidy path. Residential trays are lighter than the trays electricians run through commercial buildings. 

Under-desk trays hang beneath a work surface and hold power strips, chargers and adapters. Wire basket trays use an open steel grid, which lets heat escape and cables drop out anywhere. Solid trough trays hide cords completely and suit desks seen from behind. 

Wall-mounted trays and raceways run along walls, baseboards or ceilings between devices. A raceway is a closed plastic or metal channel, often with a snap-on cover. Choose the type by where the cables travel and how much you want them hidden. 
| Tray type | Where it goes | Main advantage | 
| Under-desk tray | Beneath a desk or table top | Holds power strips out of sight | 
| Wire basket tray | Under desks, along walls or ceilings | Open grid for airflow and easy cable exits | 
| Solid trough tray | Under desks seen from the room | Hides cords fully | 
| Wall raceway | Along walls and baseboards | Covers cords between outlets and devices |  

## Plan the cable route before you drill 

Planning the cable route comes first, because the tray must reach every device it serves. Sketch the desk or wall, marking each outlet, monitor, computer and router. Note where cables must drop down to the floor or rise to a wall outlet. 

Measure the full length of the run, then add room for corners and drops. Tray sections come in fixed lengths, so you may need to join two or cut one. Under a desk, keep the tray clear of drawers, legs, keyboard trays and knee space. 

The cable load decides how wide and deep the tray needs to be. Count the plugs, adapters and power bricks, since these take far more room than cords. Leave spare space for cables you add later, rather than filling the tray to the brim. 

## Tools and mounting hardware for the job 

A cable tray installation needs only basic tools for desk and wall trays. Gather a tape measure, pencil, level, drill and a screwdriver or driver bit. A stud finder or detector helps locate framing and hidden services in walls. 

Mounting hardware should match the surface you are fixing into, not just the tray. Wood screws suit solid wood and thick particleboard desk tops. Hollow walls need anchors rated for the load, or screws driven into studs. Masonry needs plugs and a masonry bit sized to those plugs. 

Screw length is critical under a desk, where a long screw can pierce the top. Measure the desk thickness and choose screws that stop well short of the surface. Check the tray kit for included screws, then confirm they fit your material. 

## Choosing brackets and setting support spacing 

Cable tray mounting brackets carry the weight of the tray and everything inside it. Under-desk trays often have built-in tabs or separate L-shaped brackets. Wall and ceiling trays use wall brackets, hangers or threaded rod supports. Pick brackets made for your tray, since mixed brands may not line up. 

Support spacing is the distance between brackets along the length of the tray. The correct spacing depends on the tray material, its size and the load it carries. Follow the figure in the manufacturer's instructions rather than guessing or stretching it. Add a bracket near each end and at every joint between sections. 

Tray fixing points need a solid backing to hold the weight over time. On a desk, fix into the thickest part of the top, away from edges. Heavy loads such as several power bricks may call for closer brackets. Never hang a loaded tray from a thin panel or a hollow-core door. 

## Cable tray installation steps under a desk 

Installing a cable management tray under a desk starts with clearing the work area. Unplug every device and lift cables away from the desk. Turning the desk over, where possible, makes drilling easier and more accurate. 

Mark the tray position on the underside, set back far enough from your knees. Hold the tray or brackets in place and mark each screw hole with a pencil. Drill shallow pilot holes, using a depth stop or tape on the bit. Fix the brackets, then hang or screw the tray onto them. 

A fitted under-desk tray should sit level and feel firm before you load it. Press down firmly on the empty tray to test each bracket. Mount the power strip inside, then route its cord to the nearest wall outlet. 

- Unplug devices and clear cables from the desk
- Mark the tray line on the underside
- Mark and drill shallow pilot holes
- Fix the brackets with screws sized to the top
- Attach the tray and test it with hand pressure
- Place the power strip and route the cables
 

## Mounting cable tray on walls and joining sections 

Mounting cable tray on a wall begins with a level line along the planned route. Mark bracket positions on that line at the spacing your instructions give. Check each spot with a detector before drilling, since walls can hide wires and pipes. 

Cable tray fittings join sections and turn corners without kinking the cables. Couplers or splice plates link straight sections end to end. Elbows handle turns, tees create branches, and drop-outs guide cables down to devices. Use fittings from the same tray system so the edges meet cleanly. 

Cutting a tray section to length is possible with the right tool for the material. Metal trays need a hacksaw or bolt cutter, while plastic trays cut with a fine saw. Smooth every cut edge with a file to protect cable jackets from nicks. Wear eye protection and gloves whenever you cut or file metal tray. 

## Quick cable tray setups without drilling 

A quick cable tray setup uses clamps or adhesive instead of screws. Clamp-on trays grip the edge of a desk and suit rented rooms or glass tops. Adhesive trays stick to a clean, flat surface and carry lighter loads. 

Fast cable tray options trade some strength for speed and easy removal. Adhesive pads can loosen with heat, heavy power bricks or rough surfaces. Check the load limit on the packaging before you fill the tray. Clean the surface with a mild cleaner and let it dry before sticking anything on. 

Freestanding options keep cables tidy when no fixing is allowed at all. A cable spine runs from desk to floor and gathers cords into one column. A cable box on the floor hides a power strip and its tangle of plugs. 

## Loading cables and knowing when to call an electrician 

Loading cables into a tray goes smoothly when you lay them in by device. Start with the longest cords, then add shorter ones on top. Secure bundles with reusable hook-and-loop ties rather than tight plastic ties. Leave a gentle loop where each cable exits so plugs are not strained. 

Separating power and data cables reduces clutter and makes later changes simpler. Use a divider or a second tray if your system offers one. Keep heat-producing adapters spaced out instead of packing them tightly together. Avoid letting cords rest on sharp tray edges or pinch points. 

Cable tray systems that carry fixed building wiring need a qualified electrician. That work involves circuits, load ratings, grounding and local electrical rules. Do not open outlets, extend circuits or wire anything into the mains yourself. A homeowner can manage plug-in devices, power strips and low-voltage cables. 

## Cable tray installation questions 

### How far apart should cable tray brackets be? 

Cable tray bracket spacing depends on the tray material, its size and the weight it holds. The manufacturer's instructions give the correct distance for each product. Place a bracket at each end and at every joint. Space brackets closer when the tray carries heavy power bricks. 

### Can I install a cable tray without drilling? 

Yes, a cable tray can go up without drilling using clamp-on or adhesive models. Clamp-on trays grip the desk edge, while adhesive trays stick to clean, flat surfaces. Both hold less weight than screwed trays, so check the stated load limit. 

### Where should a cable tray go under a desk? 

A cable tray under a desk goes toward the back edge, clear of your knees and drawers. That position keeps cords close to the wall outlets and out of sight. Fix the tray into the thickest part of the top with screws shorter than its thickness. 

### Do I need an electrician to install a cable tray? 

No, an under-desk or wall tray for plug-in cords does not need an electrician. Fitting one takes basic tools plus care around hidden wires or pipes. A cable tray system for fixed building wiring does need a qualified electrician. 

### What tools do you need to fit a cable tray? 

Fitting a cable tray needs a tape measure, pencil, level, drill and driver. A stud finder helps on walls, while masonry calls for a matching bit with plugs. Screws or anchors should suit the surface material and the tray weight.
