# Choose Inexpensive Window Treatments for Sliding Glass Doors

How to cover sliding glass doors on a budget: measure the opening, choose curtains, vertical blinds or panel tracks, and plan the hardware and door access.

Inexpensive window treatments for sliding glass doors come down to a few workable types: curtain panels on a wide rod, vertical blinds, and sliding panel tracks. Each type covers a large opening with stock sizes and simple mounting hardware, so the cost stays low. The choice depends on how the door opens, how much light you want to control, and how much wall space sits beside the frame. 

- Measure the full opening plus the trim before you shop, because sliding doors are wider than standard windows.
- A curtain rod must extend past both sides of the door so the panels stack clear of the glass.
- Vertical blinds and panel tracks both slide sideways, which suits a door that opens on one side.
- Mount hardware into wall studs or the header above the door, not into the thin door frame.
- Leave the sliding panel side free so the door can open without pushing through fabric.
 

## Start with the door and the opening size 

Accurate measurements decide which inexpensive treatments will fit a sliding glass door. Measure the width of the whole opening from outer trim to outer trim, then measure the height from the floor or sill to the top of the trim. Write both numbers down before you compare products. 

Sliding glass doors are wide, so stock panels sold for single windows rarely cover one. Note which side of the door slides and which side stays fixed, because that decides where fabric or slats can hang. Check the depth of the wall and trim above the door, since the mounting hardware needs a flat surface to sit against. 

Measurements for curtains on a sliding door include the rod, not just the glass. Add extra width on each side for the panels to stack when the door is open. A door that reaches the floor needs a rod placed high enough that the hem clears the track. 

## Compare the low-cost covering types 

Three covering types keep the cost down for a sliding glass door: curtain panels, vertical blinds, and sliding panel tracks. Curtain panels are fabric hung from a rod and give the softest look. Vertical blinds hang narrow slats that turn for light control and slide to one side. 

Panel tracks carry wide, flat panels that slide past each other on a track, much like a sliding door itself. Affordable panel track blinds suit a wide opening because the track spans the whole width in one piece. Each type uses different mounting hardware, so pick the type before you buy brackets. 

Cost depends on the width of the opening, the fabric or slat material, and whether the track comes in a stock length. A wide door may need two rod brackets or a longer track, which changes the total. Compare the full kit rather than the panel alone. 
| Type | How it opens | Good for | 
| Curtain panels | Pulls sideways by hand | Soft look, wall space beside the door | 
| Vertical blinds | Slats slide and tilt | Light control on a fixed side | 
| Panel tracks | Wide panels slide past each other | Very wide openings with little wall space |  

## Plan the curtain rod width over the door 

Curtain rod width over a sliding door should extend beyond the frame on both sides. The extra length lets the open panels sit over the wall instead of over the glass. A rod that stops at the frame leaves the door blocked when the curtains are drawn open. 

Choose a rod rated for the weight of the panels and long enough for the full span. Add a center bracket on a wide rod so it does not sag in the middle. Brackets attach to the wall or to the header above the door, and they set how far the fabric hangs from the glass. 

Curtains for patio doors work well when the panels stack on the fixed side of the door. Drapes beside a sliding door can also frame the opening on both sides if the wall allows. Check that the stacked fabric does not cover a light switch or block a walkway. 

## Keep door access clear 

Door access is the first thing to protect when you hang anything over a sliding glass door. The sliding panel needs a clear path along its track, so no fabric, cord or slat should cross it. Test the door by opening and closing it fully before you finish the installation. 

Hang curtains so the panels rest on the fixed side and pull toward the wall. A panel that hangs over the sliding side will catch on the handle and wear at the edge. Vertical blinds need the same check, because the slats must gather at one end without meeting the moving panel. 

Leave the floor clear under the door track. Long curtains that drag on the floor collect dust and can jam under the sliding panel. Shorten the hem or choose a length that stops just above the track. 

## Mount hardware safely and simply 

Mounting hardware holds the whole treatment, so it must attach to solid material. Wall studs and the header above a sliding door carry weight well. The thin metal or vinyl of the door frame itself does not, and screws pulled from it can drop the rod. 

Find the studs with a stud finder before you drill, and mark the bracket positions in line with each other. Use anchors suited to the wall material where no stud sits behind a bracket. A level rod or track keeps the panels hanging evenly and sliding smoothly. 

Drilling near glass or electrical wiring calls for care, and a job above your comfort level needs a trained installer. Ask a specialist to mount a heavy track or to work around wiring inside the wall. Simple brackets on a clear wall are a task many homeowners handle themselves. 

## Control light and privacy on a budget 

Light control on a sliding glass door comes from the covering type more than the price. Vertical blinds tilt to cut glare while still letting some light through. Panel tracks slide to cover part of the opening, and curtains close fully for privacy at night. 

A lined curtain panel blocks more light than an unlined one, and the lining also protects the fabric from sun. For a low-cost option, choose a tight-weave fabric in a medium tone. Sheer panels soften the view but give little privacy after dark. 

Layer a light covering with a heavier one only if the wall has room for two rods. A single rod with panels that close fully covers both privacy and light needs for many rooms. Match the covering to how the room is used rather than to a trend. 

## Fit the treatment to the room 

The room layout decides which inexpensive treatment looks right beside a sliding glass door. Furniture placed close to the door leaves little wall for a stacked curtain, so a panel track or vertical blind may fit better. A room with open wall space on one side suits curtain panels. 

Consider the path people walk through the room. A curtain that billows into a walkway catches on chairs and tables. Slim vertical blinds and flat panel tracks take less floor space when they gather at the side. 

Match the hardware finish to the other fittings in the room, such as door handles and light fixtures. A consistent finish makes an inexpensive treatment read as part of the design. Draw the layout on paper before you order, so the covering and the furniture do not compete for the same corner. 

## Check the order before you buy 

A final check of the order prevents a return and a second trip. Confirm the width and height against your measurements, and confirm that the kit includes brackets or a track. Some products sell the hardware separately, which changes the total cost. 

Read what the package covers for the track length and the number of panels or slats. A stock track may need a connector for a wide door, and that part should be in the order. Check the mounting surface depth so the brackets fit the wall above the door. 

Keep the receipt and the packaging until the treatment is mounted and the door opens freely. A quick test of the sliding action shows whether the hardware sits in the right place. Adjust the brackets before you discard the box. 

## Questions about sliding glass door coverings 

### What are inexpensive window treatments for sliding glass doors? 

Curtain panels on a wide rod, vertical blinds, and sliding panel tracks are the low-cost options for a sliding glass door. Each type uses stock sizes and basic mounting hardware. The right one depends on the width of the opening and the wall space beside the door. 

### How do I measure a sliding door for curtains? 

Measure the full opening from outer trim to outer trim and the height from floor or sill to the top of the trim. Then add extra width on each side for the rod and the stacked panels. Measure the wall depth above the door so the brackets have a flat surface. 

### How wide should the curtain rod be over a sliding door? 

The curtain rod should extend past the door frame on both sides, so the open panels rest on the wall rather than over the glass. A rod that stops at the frame blocks the door when the curtains are drawn open. Add a center bracket on a long span to stop the rod from sagging. 

### Do vertical blinds work on a sliding glass door? 

Vertical blinds work well on a sliding glass door because the slats slide to one side and tilt for light control. They take little floor space and suit a door with limited wall beside it. Check that the gathered slats clear the sliding panel before you mount the track. 

### Can I hang curtains without blocking the door? 

Yes, curtains can hang over a sliding glass door without blocking it when the rod extends past the frame and the panels stack on the fixed side. Keep the fabric clear of the sliding panel and the handle. Test the door through a full opening before you finish. 

### Is it safe to mount a curtain rod above a sliding door myself? 

Mounting a light curtain rod into wall studs or the header above the door is a task many homeowners can do with a drill and a level. Work that involves heavy tracks, glass, or wiring inside the wall needs a trained specialist. Stop and call one if you are unsure what sits behind the wall.
